0284349 DECAL SET, 100 EVINRUDE
E100STLEND, E100STLERC, E100STLETS, E115JLEND, E115JLERC, E115JLETS, E88MSLENB, E88MSLENB, E88MSLERD, E88MSLERD, E88MSLETE, E88MSLETE
DECAL

Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- ENGINE COVER - EVINRUDE » 0284349
E100STLETS, VE100SLETS 1993
E115JLEND, E115MLEND, E115TLEND, E115TXEND, TE115TLEND 1992
E115JLERC, E115MLERS, E115TLERC, E115TXARS 1994
E115JLETS, E115MLETS, E115TLETS, E115TXATS, TE115TLETS, VE115TLETS 1993
E88MSLENB 1992
E88MSLENB, E90JLEND, E90TLEND, TE90TLEND, VE90MLEND, VE90TLEND 1992
E88MSLERD, E90JLERC, E90MLERC, E90TLERC, E90TXARC 1994
E88MSLERD 1994
E88MSLETE 1993
E88MSLETE, E90JLETS, E90TLETS, E90TXATS, TE90TLETS, VE90MLETS, VE90TLETS 1993
Information:
START BY:a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) which shows the direction of the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 6 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plate from each side of the No. 4 upper main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. Install the main bearings dry when clearance checks are made. Put clean engine oil on the main bearings for final assembly. 5. Install the lower bearings in the bearing caps.6. Install the upper bearings in the cylinder block with tool (A). Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block. When the bearing clearance is checked and the engine is in a vertical position such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearance.7. Check the bearing clearance with Plastigage (B) as follows:
When Plastigage is used to check bearing clearances, do not use an impact wrench for the torque tightening sequence. However, an impact wrench can be used for the final tightening torque.
a. Put clean oil on the threads of the cap bolts. Install the caps and cap bolts, finger tight.b. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb.ft.).c. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb.ft.).d. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120° 5° more. Tighten the bolts on the tab end of the cap 120° 5° more. Make sure the main bearing caps are installed with their identification number (7) in alignment with the identification number on the side of the cylinder block and arrow (6) toward the front of the block.8. Remove the main bearing caps and tool (B).9. Measure the thickness of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to .0073 in.). The maximum clearance for used bearings is 0.25 mm (0.010 in.).10. Install a thrust plate (8) on each side of the No. 4 upper bearing. Install the thrust plates with the side marked "BLOCK SIDE" toward the cylinder block.11. Install No. 2 through 6 main bearing caps. Follow the tightening procedure in Step 7. 12. Do Steps 2, 4 through 9 and 11 for the No. 1 and No. 7 main bearing caps. Check the end play of the crankshaft with tool (C). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.152 to 0.508 mm (0.0059 to 0.0200 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 inEND BY:a. install oil pump
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. Install the main bearings dry when clearance checks are made. Put clean engine oil on the main bearings for final assembly. 5. Install the lower bearings in the bearing caps.6. Install the upper bearings in the cylinder block with tool (A). Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block. When the bearing clearance is checked and the engine is in a vertical position such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearance.7. Check the bearing clearance with Plastigage (B) as follows:
When Plastigage is used to check bearing clearances, do not use an impact wrench for the torque tightening sequence. However, an impact wrench can be used for the final tightening torque.
a. Put clean oil on the threads of the cap bolts. Install the caps and cap bolts, finger tight.b. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb.ft.).c. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb.ft.).d. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120° 5° more. Tighten the bolts on the tab end of the cap 120° 5° more. Make sure the main bearing caps are installed with their identification number (7) in alignment with the identification number on the side of the cylinder block and arrow (6) toward the front of the block.8. Remove the main bearing caps and tool (B).9. Measure the thickness of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to .0073 in.). The maximum clearance for used bearings is 0.25 mm (0.010 in.).10. Install a thrust plate (8) on each side of the No. 4 upper bearing. Install the thrust plates with the side marked "BLOCK SIDE" toward the cylinder block.11. Install No. 2 through 6 main bearing caps. Follow the tightening procedure in Step 7. 12. Do Steps 2, 4 through 9 and 11 for the No. 1 and No. 7 main bearing caps. Check the end play of the crankshaft with tool (C). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.152 to 0.508 mm (0.0059 to 0.0200 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 inEND BY:a. install oil pump
Parts decal EVINRUDE:
0283782
0283782 DECAL SET, 88 models
E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E110MLCEM, E112TSLERS, E115JLEIE, E115JLEND, E115JLERC, E115JLETS, E115MLESB, E88MSLCER, E88MSLCER, E88MSLEIM, E88MSLEIM, E88MSLENB, E88MSLENB, E88MSLERD, E88MSLERD, E88MSLESA, E
0335117
0335117 DECAL, Exh. hsg., Jo.
E100STLEIE, E100STLEND, E100STLESB, E100STLETS, E115JLEIE, E115JLEND, E115JLETS, E115MLESB, E28ESLENE, E28ESLENE, E28ESLETD, E28ESLETD, E48ESLEIM, E48ESLEIM, E48ESLENB, E48ESLENB, E48ESLESA, E48ESLESA, E48ESLETE, E48ESLETE, E88MSLEIM, E88MSLEIM, E88M
0284273
0284273 DECAL SET, 90/115
E100STLEIE, E100STLEND, E100STLETS, E115JLEIE, E115JLEND, E115JLETS, E88MSLEIM, E88MSLEIM, E88MSLENB, E88MSLENB, E88MSLETE, E88MSLETE
0338445
0338445 DECAL, Exhaust hsg., Jo
BE10EEDD, BE10RELEUS, BE15EEDS, BE15RELEUC, E100STLEND, E100STLETS, E10EENA, E10EETM, E115JLEND, E115JLETS, E120TLEND, E120TLETF, E125ESXENR, E125ESXETA, E140CXATF, E140CXENM, E150ELENC, E15EENM, E15EETB, E175EXENC, E185ESXETA, E200CXATF, E20CREND, E
0284344
0284344 DECAL SET
E100STLEND, E100STLERC, E100STLETS, E115JKLERS, E115JLEND, E115JLERC, E115JLETS, E85TTLEND, E85TTLERC, E85TTLETS, E88MSLENB, E88MSLENB, E88MSLERD, E88MSLERD, E88MSLETE, E88MSLETE
0284347
0284346
0284346 DECAL SET, 90/115, 25"
E100STLEND, E100STLETS, E115JLEND, E115JLETS, E88MSLENB, E88MSLENB, E88MSLETE, E88MSLETE
0338173
0338173 DECAL, Lower covers, Quiet Rider
E100STLEND, E100STLERC, E100STLETS, E115JLEND, E115JLERC, E115JLETS, E150ELERA, E150ELETG, E175EXARC, E175EXATG, E88MSLENB, E88MSLENB, E88MSLERD, E88MSLERD, E88MSLETE, E88MSLETE