0284814 DECAL SET, Ev., 5 Models EVINRUDE
BE5DREDS, BE5DREUC, BE6DREDS, BE6DREUC, BE8REDS, E6REOD, E8REOD, E8REUC
DECAL

Price: query
Rating:
BRP EVINRUDE entire parts catalog list:
- ENGINE COVER » 0284814
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E6REOD, E6RLEOD, E6SLEOD 1995
E8REOD, E8RLEOD, E8SRLEOD 1995
E8REUC, E8RLEUC, E8SRLEUC 1997
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
B 9S-3263 Thread Lock Compound 1
C 8T-2998 Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01039504
Thoroughly clean the gasket material from the cylinder block.
Install a new gasket (25) and O-ring seals (26) on the cylinder block.Note: On newer blocks, an integral seal is used instead of O-ring seals (26) and gasket (25) .
Illustration 2 g00576208
Illustration 3 g01032116
Thoroughly clean all gasket material from both sides of plate (23). Install plate (23) and bolts (24) .
Install shaft assembly (20). Apply Tooling (B) to the studs and to the bolt for shaft assembly (20). Tighten the nuts and the bolt for shaft assembly (20) to a torque of 55 10 N m (41 7 lb ft).Note: The backlash for the camshaft gear and for the adjustable idler gear will need to be readjusted if shaft assembly (19) has been removed, loosened, or moved in any way. The camshaft gear must be installed and the adjustable idler gear must be removed in order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear Group (Front) - Time".
Install shaft assembly (19). Do not tighten the nuts and the bolt for shaft assembly (19) at this time. The nuts and the bolt for shaft assembly (19) will need to be tightened when the backlash is adjusted.
Apply Tooling (B) to bolts (22). Install shaft assembly (21). Tighten bolts (22) to a torque of 55 10 N m (41 7 lb ft) in the following sequence: (1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1).
Illustration 4 g01074541
Illustration 5 g00516404
Put cluster gear (15) on shaft assembly (21). Ensure that Timing Marks (V) are aligned on the cluster gear and on the crankshaft gear. Apply Tooling (B) to bolts (16). Install plate (17) and bolts (16). Tighten bolts (16) to a torque of 30 7 N m (22 5 lb ft).
Illustration 6 g01074542
Position idler gear (11) on shaft assembly (20). Apply Tooling (B) to bolts (12). Install plate (13) with the oil groove toward the gear face. Install bolts (12) and tighten the bolts to a torque of 30 7 N m (22 5 lb ft).
Illustration 7 g01074546
Note: Skip Step 9 if shaft assembly (19) has been removed, loosened, or moved in any way. The backlash for the camshaft gear and for the adjustable idler gear will need to be readjusted. The camshaft gear must be installed and the adjustable idler gear must be removed in order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear Group (Front) - Time".
Position adjustable idler gear (7) on shaft assembly (19). Apply Tooling (B) to bolts (8). Install plate (9) and bolts (8). Tighten bolts (8) to a torque of 30 7 N m (22 5 lb ft).
Illustration 8 g00576240
Illustration 9 g01039529
Install O-ring seals (5) and (6) in seal assembly (3). Lubricate seal (6) with a 50/50 mixture of Tooling (C) and engine oil.
Assemble thrust plate (1) and seal assembly (3). Apply Tooling (B) to bolts (2). Hold the assembly in position and install bolts (2). Evenly tighten bolts (2) until seal assembly (3) and O-ring seal (5) are seated against the cylinder head.Note: Be careful in order to ensure that O-ring seal (5) stays in the groove in seal assembly (3) .
Install adapter (4). Ensure that the dowel in adapter (4) engages the hole in the camshaft.
Adjust the backlash for the camshaft gear and for the adjustable idler gear, if necessary. Refer to Testing and Adjusting, "Gear Group (Front) - Time".Note: The camshaft gear must be installed and the adjustable idler gear must be removed in order to perform the backlash adjustment procedure.End By: Install the front housing. Refer to Disassembly and Assemb
Parts decal EVINRUDE:
0435610
0435610 DECAL SET, Jo., 8 Models
BE5DREDS, BE6DREDS, BE8REDS, E6RENM, E6REOD, E6RERE, E6RETB, E8RENM, E8REOD, E8RERE, E8RETB
0435611
0435611 DECAL SET, Jo., 8 Sail
BE5DREDS, BE6DREDS, BE8REDS, E6RENM, E6REOD, E6RERE, E6RETB, E8RENM, E8REOD, E8RERE, E8RETB
0435608
0435608 DECAL SET, Jo., 6 Models
BE5DREDS, BE6DREDS, BE8REDS, E6RENM, E6REOD, E6RERE, E6RETB, E8RENM, E8REOD, E8RERE, E8RETB
0284816
0284816 DECAL SET, Ev., 8 Models
BE5DREDS, BE5DREUC, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8REDS, E6REOD, E8REOD, E8REUC
0284815
0284815 DECAL SET, Ev., 6 Models
BE5DREDS, BE5DREUC, BE6DREDS, BE6DREUC, BE8REDS, E6REOD, E8REOD, E8REUC
0437732
0435607
0437731