5032529 EVINRUDE *DECAL, Stbd.


5032529 *DECAL, Stbd. EVINRUDE E25EL4SIC, E30EL4SIC DECAL
5032529 *DECAL, Stbd. EVINRUDE
Rating:
33

Buy *DECAL, Stbd. 5032529 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$41.43
 

24-09-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials CEM650 147 (2000-2010) Car Mat Set, Grey with Black Trim, Premium
Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model. || Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Alfa Romeo 147 (2000-2010)
Number on catalog scheme: 11
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001

Information:

Introduction
This Special Instruction provides a parts list and an installation procedure for a new crankcase breather system. The breather is for the C27 engines that are used on 990H Large Wheel Loaders and 844H Large Wheel Dozers. The new system will reduce the carryover of oil from the current system by removing the breather that is located in the rear housing and relocating the breather in the valve covers.Required Parts
Table 1
Required Parts    
Part Number     Part Name     Quantity    
126-0559     Bolts     4    
146-7453     Hose     180 cm (71 inch)    
198-4777     Hard Washer     1    
223-1993     Covers     2    
224-7506     Isolation Seals     2    
227-5538     O-Ring Seal     1    
273-8703     Cover     1    
272-7013     Hose     2    
289-9139     Band Clamps     4    
292-5534     Elbows     2    
294-0536     Identification Plate     1    
295-6463     Tube As     1    
2N-8109     Clamps     2    
300-6911     Bracket As     1    
300-6912     Bracket As     1    
304-0455     Tube     1    
306-3060     Bracket As     1    
4D-7388     Clips     2    
4N-4668     Breather As     2    
4S-1962     Clip     1    
5M-3062     Bolt     1    
5P-7470     Clips     2    
5P-7471     Clips     2    
5P-7703     Grommets     2    
5P-8211     O-Ring Seals     2    
6V-3831     O-Ring Seals     2    
8T-4121     Hard Washers     2    
8T-4133     Nut     1    
8T-4136     Bolt     1    
8T-4223     Hard Washers     2    
8T-4896     Hard Washers     2    
8T-4956     Bolts     2    
9M-2904     Hose Clamps     4    Installation Procedure
Illustration 1 g01393639
Remove the side panel (1) and side panel (2) from the machine.
Illustration 2 g01393473
Panel (3) that is located underneath the catwalk can be removed in order to access to the rear of the engine.
Illustration 3 g01395997
Remove the valve covers (4) from the right side of the engine.
Illustration 4 g01399984
(4) 223-1993 Cover (5) 294-0536 Identification Plate (6) 4N-4668 Breather As (7) 6V-3831 O-Ring Seal (8) 2N-8109 Clamp (9) 126-0559 Bolt (10) 292-5534 Elbow (11) 5P-8211 O-Ring Seal (12) 224-7506 Isolation Seal
Illustration 5 g01400550
(12) 295-6463 Tube As
Assemble new valve covers that are shown in Illustration 4. Once the breather (6) has been assembled, install the breather on the engine.
Feed the breather tube (12) into position, but do not make any connections. The tube must remain loose until the new coolant line has been installed. You may also need to remove the exhaust pipe between the turbocharger and the muffler.
Drain the coolant into a suitable device that can hold 150 L (40 US gal) of fluid. The coolant will be reused once the lines have been changed. Refer to Operation and Maintenance Manual, SEBU7886, "Cooling System Coolant-Change" for information on draining and filling the cooling system.
Remove the coolant line that is between the tank and the water pump.


Parts decal EVINRUDE:

5030204
 
5030204 DECAL, Shift
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E5RECS
5030226
 
5030226 DECAL, Stop
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E5RECS
5031127
 
5031127 DECAL, Front
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC, E70, E70PL4EEC
5032040
 
5032040 DECAL, Warning
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032156
 
5032156 DECAL, Engine start
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032531
 
5032531 *DECAL, Port
E25EL4SIC, E30EL4SIC
5032532
 
5032532 DECAL, Emblem rear, 25
E25EL4SIC, E30EL4SIC
5032533
 
5032533 DECAL, Emblem rear, 30
E25EL4SIC, E30EL4SIC
Back to top