5041410 EVINRUDE DRIVE SHAFT HOUSING ASSEMBLY


5041410 DRIVE SHAFT HOUSING ASSEMBLY EVINRUDE B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS, E10EL4INS, E10PL4INS DRIVE
5041410 DRIVE SHAFT HOUSING ASSEMBLY EVINRUDE
Rating:
43

Buy DRIVE SHAFT HOUSING ASSEMBLY 5041410 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

B10EL4AAA, E10EL4AAA 2012
B10EL4INS 2012
B10PL4AAA, B10PX4AAA, E10PL4AAA, E10PX4AAA 2012
B10PL4INS 2012
B10PX4INS, E10PX4INS 2012
B10R4AAA, B10RL4AAA, E10R4AAA, E10RL4AAA 2012
B10R4INS, E10R4INS 2012
B10RL4INS, E10RL4INS 2012
B10TEL4AAA, E10TEL4AAA 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4AAA, B10TPX4AAA, E10TPL4AAA, E10TPX4AAA 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012
E10EL4INS 2012
E10PL4INS 2012

Information:

1. Remove oil tube (1) from the engine.2. Fasten a hoist to support (2) with Tooling (A) and remove support (2) from the drive housing. The weight of the support is approximately 102 kg (225 lb). 3. Remove elbow (3) and tube (4) as a unit from the engine. 4. Remove the bolts and use Tooling (B) to remove shaft (6) and idler gear (5) from the drive housing. 5. If necessary, use Tooling (C) to remove the bearing from idler gear (5). 6. Remove washer (7) from the inside of the drive housing. 7. Remove bolt (9) and washer to remove clip (8) from the drive housing. 8. Remove cover (11) from the drive housing.9. Remove all of the bolts that hold the engine oil pan to the egine. Install 3/8-16 NC guide bolts in each side of the engine oil pan. Fasten a hoist to the engine and lift the engine approximately 12 mm (.5 in) off of the engine oil pan. Put two 50 mm wide × 100 mm long × 6 mm thick (2 in wide × 4 in long × 1/4 in thick) plates in position between the cylinder block and the engine oil pan on each side of the engine. Lower the engine on the plates and remove the hoist. The weight of the 3508 Engine is approximately 4445 kg (9800 lb). The weight of the 3512 Engine is approximately 5902 kg (13 000 lb). The weight of the 3516 Engine is approximately 7718 kg (17 000 lb).
Fuel control linkage (10) must be moved for clearance to pull the front drive housing from the engine or damage to parts can be the result.
10. Fasten a hoist to front drive housing (12) with Tooling (A). Remove bolts (13) and the remainder of the bolts that hold housing (12) in position. Remove front drive housing (12) from the engine. The weight of the housing is approximately 209 kg (460 lb).Install Front Drive Housing
1. Put the housing gasket in position on the front of the cylinder block. Install two 5/8-11 NC guide bolts (1) in the cylinder block. 2. Fasten a hoist to front drive housing (2) with Tooling (A). Put housing (2) in position on the guide bolts and install the bolts to hold it in position. Remove the guide bolts and install the remainder of the bolts. Tighten all the bolts evenly and cut the housing gasket even with the bottom of the cylinder block.3. Fasten a hoist to the engine and lift the engine enough to remove the plates between the cylinder block and the engine oil pan. If the engine oil pan gasket is damaged, the engine will have to be removed from the engine oil pan to make a replacement of the gasket. Lower the engine on the engine oil pan and remove the guide bolts from the engine oil pan. Install all of the bolts and hold the engine oil pan to the engine. 4. Put clean engine oil on the O-ring seals and install cover (3) on the drive housing. 5. Put washer (4) in position inside the drive housing. 6. Use Tooling (B) and a press to install the bearing in idler gear (5). Check the bore in the bearing after assembly. The bore in the bearing must be 90.00 0.06 mm (3.543 .002 in). 7. Put clean oil on the O-ring seal on shaft (6). Install idler gear (5) and shaft (6) in the front drive housing. 8. Make sure the gasket and seals are in position and install aftercooler water line (7) on the engine. Install clip (8) on the drive housing. 9. Install oil tube (9) on the engine.10. Fasten a hoist to support (10) with Tooling (A) and put it in position on the front drive housing. Install the bolts to hold the support in position. Anytime the front crankshaft seal and wear sleeve are removed a new seal and wear sleeve must be installed.End By:a. install governor fastener groupb. install accessory drive (front)c. install front crankshaft seal and wear sleeved. install crankcase breathere. install engine oil filter housing


Parts drive EVINRUDE:

5041409
 
5041409 DRIVE SHAFT HOUSING ASSEMBLY
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS, E10EL4INS, E10PL4INS
5040506
DRIVE SHAFT BUSHING
5040506 DRIVE SHAFT BUSHING
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS, E10EL4INS, E10PL4INS
5041351
 
5041351 DRIVE SHAFT ASSEMBLY
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5041352
 
5041352 DRIVE SHAFT ASSEMBLY
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5041353
 
5041353 DRIVE SHAFT ASSEMBLY
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5040262
 
5040262 DRIVE GEAR
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5041317
 
5041317 DRIVE PULLEY
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
Back to top