0435497 DRIVESHAFT & SLEEVE AY. EVINRUDE
BE115TLEDA, E100STLEND, E100STLERC, E100STLETS, E115JKLEOC, E115JKLERS, E115JLEND, E115JLEOR, E115JLERC, E115JLETS, E115JLEUM, E85TTLEOR, E85TTLERC, E88MSLEDC, E88MSLEDC, E88MSLENB, E88MSLENB, E88MSLEOS, E88MSLEOS, E88MSLERD, E88MSLERD, E88MSLETE, E8
DRIVESHAFT
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- JET DRIVE UNIT » 0435497
E100STLERC 1994
E100STLETS, VE100SLETS 1993
E115JKLEOC 1995
E115JKLERS 1994
E115JLEND, E115MLEND, E115TLEND, E115TXEND, TE115TLEND 1992
E115JLEOR, E115MLEOR, E115TLEOR, E115TXAOR 1995
E115JLERC, E115MLERS, E115TLERC, E115TXARS 1994
E115JLETS, E115MLETS, E115TLETS, E115TXATS, TE115TLETS, VE115TLETS 1993
E115JLEUM 1997
E85TTLEOR 1995
E85TTLERC 1994
BE90TLEDA, E88MSLEDC, E90TLEDA, HE88MSLEDC, HE90MLEDA, HE90TXADA 1996
E88MSLEDC, HE88MSLEDC 1996
E88MSLENB 1992
E88MSLENB, E90JLEND, E90TLEND, TE90TLEND, VE90MLEND, VE90TLEND 1992
E88MSLEOS, E90JLEOR, E90MLEOR, E90TLEOR 1995
E88MSLEOS 1995
E88MSLERD, E90JLERC, E90MLERC, E90TLERC, E90TXARC 1994
E88MSLERD 1994
E88MSLETE 1993
E88MSLETE, E90JLETS, E90TLETS, E90TXATS, TE90TLETS, VE90MLETS, VE90TLETS 1993
Information:
start by:a) remove oil pan1. Check each main bearing cap for its location on the engine. Each cap has a number which gives the location of that cap. Make a note that the number on each cap is toward the front of the cylinder block. 2. Remove the bolts and washers that hold main bearing cap (2) in place. Remove the bearing cap and the lower half of the main bearing. Use tool (C) to remove the bolts that hold the No. 1 main bearing cap in position.3. Remove bearing (1) from the bearing cap. 4. Turn the crankshaft until tool (A) can be installed in the oil hole in the crankshaft journal. Install tool (A). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
5. Put clean engine oil on the lower bearings. Install lower bearings in the bearing caps.6. Put clean engine oil on the upper bearings (the bearing with the oil hole). Install upper bearings in the cylinder block with tool (A). Make sure the tab on the back of the bearings fits in the groove of the caps and cylinder block.
When bearing caps are installed, make sure the number on the side of the cap is next to and respective with the number on the engine block.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn crankshaft when Plastigage is in position to check clearance. 7. Check the bearing clearance with tool (B) as follows: Put cap (3) in position and install the bolts. Tighten bolt (5) to a torque of 41 4 N m (30 3 lb.ft.). Tighten bolt (4) to a torque of 41 4 N m (30 3 lb.ft.). Put a mark on both bolt heads and the bearing cap. Tighten bolt (4) 120° 5° more. Tighten bolt (5) 120° 5° more.8. Remove the bearing cap and measure the thickness of the Plastigage. The main bearing clearance must be 0.076 to 0.168 mm (.0030 to .0066 in.). The maximum permissible clearance is 0.18 mm (.007 in.).9. Put clean SAE 30 oil on the bolt threads, washer faces and lower half of the main bearing. Put the bearing cap and lower half of the main bearing in position on the engine. Install the bolts. Tighten bolt (5) to a torque of 41 4 N m (30 3 lb.ft.). Tighten bolt (4) to a torque of 41 4 N m (30 3 lb.ft.). Put a mark on both bolt heads and the cap. Tighten bolt (4) 120° 5° more. Tighten bolt (5) 120° 5° more.10. Do Steps 1 through 9 for the remainder of the bearings. 11. Check the crankshaft end play with tooling (D). The end play is controlled by the thrust bearing on No. 4 main bearing. The end play with new bearings must be 0.08 to 0.25 mm (.003 to .010 in.). The maximum permissible end play with used bearings is 0.36 mm (.014 in.).end by:a) install oil pan
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
5. Put clean engine oil on the lower bearings. Install lower bearings in the bearing caps.6. Put clean engine oil on the upper bearings (the bearing with the oil hole). Install upper bearings in the cylinder block with tool (A). Make sure the tab on the back of the bearings fits in the groove of the caps and cylinder block.
When bearing caps are installed, make sure the number on the side of the cap is next to and respective with the number on the engine block.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn crankshaft when Plastigage is in position to check clearance. 7. Check the bearing clearance with tool (B) as follows: Put cap (3) in position and install the bolts. Tighten bolt (5) to a torque of 41 4 N m (30 3 lb.ft.). Tighten bolt (4) to a torque of 41 4 N m (30 3 lb.ft.). Put a mark on both bolt heads and the bearing cap. Tighten bolt (4) 120° 5° more. Tighten bolt (5) 120° 5° more.8. Remove the bearing cap and measure the thickness of the Plastigage. The main bearing clearance must be 0.076 to 0.168 mm (.0030 to .0066 in.). The maximum permissible clearance is 0.18 mm (.007 in.).9. Put clean SAE 30 oil on the bolt threads, washer faces and lower half of the main bearing. Put the bearing cap and lower half of the main bearing in position on the engine. Install the bolts. Tighten bolt (5) to a torque of 41 4 N m (30 3 lb.ft.). Tighten bolt (4) to a torque of 41 4 N m (30 3 lb.ft.). Put a mark on both bolt heads and the cap. Tighten bolt (4) 120° 5° more. Tighten bolt (5) 120° 5° more.10. Do Steps 1 through 9 for the remainder of the bearings. 11. Check the crankshaft end play with tooling (D). The end play is controlled by the thrust bearing on No. 4 main bearing. The end play with new bearings must be 0.08 to 0.25 mm (.003 to .010 in.). The maximum permissible end play with used bearings is 0.36 mm (.014 in.).end by:a) install oil pan
Parts driveshaft EVINRUDE:
0335722
0335722 DRIVESHAFT, Lower
BE115TLEDA, E100STLEIE, E100STLEND, E100STLERC, E100STLETS, E112TSLEDR, E112TSLEDR, E112TSLEOC, E112TSLEOC, E112TSLERS, E115JKLEOC, E115JKLERS, E115JLEIE, E115JLEND, E115JLEOR, E115JLERC, E115JLETS, E115TSLECM, E115TSLEUA, E120TLEIE, E120TLEND, E120T
0337058
0337058 DRIVESHAFT, Upper
E100STLEND, E100WTLENE, E115JLEND, E120TLEND, E125ESXENR, E140CXENM, E155WTLENE, E185ESXENR, E200CXENE, E225CXENR, E85TTLEND, E88MSLENB, E88MSLENB
0337059
0337059 DRIVESHAFT, Upper
E100STLEND, E100WTLENE, E115JLEND, E120TLEND, E125ESXENR, E140CXENM, E155WTLENE, E185ESXENR, E200CXENE, E225CXENR, E88MSLENB, E88MSLENB
0435766
0435766 DRIVESHAFT, Upper
BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, E100STLERC, E100STLETS, E112TSLEDR, E112TSLEDR, E112TSLEOC, E112TSLEOC, E112TSLERS, E115JLEOR, E115JLERC, E115JLETS, E120TLERC, E120TLETF, E125ESXERK, E125ESXETA, E130CXAOR, E140CXARC, E140CXATF, E185ES
0435765
0435765 DRIVESHAFT, Upper
BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, E100STLERC, E100STLETS, E112TSLEDR, E112TSLEDR, E112TSLEOC, E112TSLEOC, E112TSLERS, E115JKLEOC, E115JKLERS, E115JLEOR, E115JLERC, E115JLETS, E120TLERC, E120TLETF, E125ESXERK, E125ESXETA, E130CXAOR, E140