0282233 EVINRUDE ENGINE COVER ASSY.


0282233 ENGINE COVER ASSY. EVINRUDE E30ECRR, E35ECRR ENGINE
0282233 ENGINE COVER ASSY. EVINRUDE
Rating:
23

Buy ENGINE COVER ASSY. 0282233 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

E30ECRR   E35ECRR   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E30ECRR, E30ELCRR 1984
E35ECRR, E35ELCRR, E35RCRR, E35RLCRR, E35TELCRR 1984

Information:


Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
100-3 Engine Oil Pressure Sensor : Voltage Above Normal The Electronic Control Module (ECM) has detected a voltage on the signal wire of the sensor that is greater than 4.95 V for ten seconds. The code is logged.
The amber warning lamp is illuminated.
The service tool displays "Error Indicator" on the status screen for this parameter.
100-4 Engine Oil Pressure Sensor : Voltage Below Normal The ECM has detected a voltage on the signal wire of the sensor that is less than 0.2 V for ten seconds.
3563-3 Engine Intake Manifold #1 Absolute Pressure : Voltage Above Normal The ECM has detected a voltage on the signal wire of the sensor that is greater than 4.95 V for five seconds. The code is logged.
The amber warning lamp is activated.
The service tool displays "Error Indicator" on the status screen for this parameter.
3563-4 Engine Intake Manifold #1 Absolute Pressure : Voltage Below Normal The ECM has detected a voltage on the signal wire of the sensor that is less than 0.2 V for five seconds.
4289-3 Aftertreatment #1 Three Way Catalytic Converter Intake Gas Temperature : Voltage Above Normal The ECM has detected a voltage on the signal wire of the sensor that is greater than 4.8 V for five seconds. The code is logged.
The amber warning lamp is activated.
The service tool displays "Error Indicator" on the status screen for this parameter.
4289-4 Aftertreatment #1 Three Way Catalytic Converter Intake Gas Temperature : Voltage Below Normal The ECM has detected a voltage on the signal wire of the sensor that is less than 0.2 V for five seconds.
4290-3 Aftertreatment #1 Three Way Catalytic Converter Outlet Gas Temperature : Voltage Above Normal The ECM has detected a voltage on the signal wire of the sensor that is greater than 4.8 V for five seconds. The code is logged.
The amber warning lamp is activated.
The service tool displays "Error Indicator" on the status screen for this parameter.
4290-4 Aftertreatment #1 Three Way Catalytic Converter Outlet Gas Temperature : Voltage Below Normal The ECM has detected a voltage on the signal wire of the sensor that is less than 0.2 V for five seconds. The following analog sensors are used by this engine:
Engine oil pressure sensor
Intake manifold pressure sensor
Temperature sensor at the inlet of the catalytic converter
Temperature sensor at the outlet of the catalytic converterBackground InformationThe ECM continuously creates a pull-up voltage on the signal wire for each sensor. The ECM uses this pull-up voltage in order to detect a problem in the signal circuit. When the ECM detects voltage that is above a threshold on the signal wire, the ECM activates a high voltage -3 diagnostic code. When the ECM detects voltage that is below a threshold on the signal wire, the ECM activates a low voltage -4 diagnostic code.Note: There may be a delay of 30 seconds for Caterpillar Electronic Technician (ET) to display an active diagnostic code. When you check for a diagnostic code, be sure to wait at least 30 seconds.The following components can cause these codes:
Electrical connector or wiring
Sensor
ECMThe most likely cause of a code is a problem with an electrical connector or wiring. The least likely cause of a code is the ECM.
Illustration 1 g03678865
Schematic for the analog sensors
Illustration 2 g01960583
Locations of the sensors that are associated with the analog signal (left side engine view)
(1) Intake manifold pressure sensor
Illustration 3 g01960587
Locations of the sensors that are associated with the analog signal (right side engine view)
(2) Engine oil pressure sensor
Illustration 4 g02471238
Locations of the analog sensors that are for the catalytic converter/muffler
(3) Temperature sensor for the inlet of the catalytic converter/muffler
(4) Temperature sensor for the outlet of the catalytic converter/muffler
Illustration 5 g01960607
Locations of the connectors at the ECM for the analog sensors
(5) Connector for the sensors at the catalytic converter
(6) J2/P2 ECM connectors
(7) J1/P1 ECM connectors
Illustration 6 g01960613
Terminal locations at the P1 ECM connector for the analog sensors
(P1-24) Temperature at the outlet of the catalytic converter
(P1-34) Analog return
(P1-41) Analog sensor supply
(P1-42) Analog sensor supply
(P1-54) Temperature at the inlet of the catalytic converter
(P1-55) Intake manifold pressure
Illustration 7 g03678891
Terminal locations at the P2 ECM connector for the analog sensors
(P2-37) Analog return
(P2-38) Analog return
(P2-46) Analog sensor supply
(P2-56) Engine oil pressure
Illustration 8


Parts engine EVINRUDE:

0329019
 
0329019 ENGINE COVER, Lower
E20CRCOS, E25ECOC, E25ECRS, E30ECOA, E30ECRR, E35ECRR
0282306
 
0282306 ENGINE COVER ASSY.
E30ECRR, E35ECRR
0282234
 
0282234 ENGINE COVER ASSY.
E30ECRR, E35ECRR
0393980
 
0393980 ENGINE COVER ASSY.
E30ECRR, E35ECRR
0393981
 
0393981 ENGINE COVER ASSY.
E30ECRR, E35ECRR
0394368
 
0394368 ENGINE COVER ASSY.
E30ECRR, E35ECRR
Back to top