0282666 EVINRUDE ENGINE COVER ASSY.


0282666 ENGINE COVER ASSY. EVINRUDE E20CRCDC, E25ECDR ENGINE
0282666 ENGINE COVER ASSY. EVINRUDE
Rating:
38

Buy ENGINE COVER ASSY. 0282666 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

E20CRCDC   E25ECDR   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E20CRCDC, E20CRLCDC, E20ECDC, E20ELCDC, E20TECDC 1986
E25ECDR, E25ELCDR, E25RCDC, E25RLCDC, E25TECDC, E25TELCDC 1986

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Codes, Logged Codes, and Electrical Connectors
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active diagnostic codes and logged codes. Specifically check for codes related to the prelubrication system.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
Codes and Electrical Connectors
Result: A diagnostic trouble code is not active or logged.
Proceed to Test Step 2.
Result: A diagnostic trouble code is active or logged.
Repair: Check for correct installation of the applicable electrical connectors.
Troubleshoot any active codes before continuing with this procedure.
Verify that the repair eliminated the problem.
2. Check for Low Quality Fuel
A. Refer to Operation and Maintenance Manual and Application and Installation Guide, LEBW4977, "Gaseous Fuels" for information on the proper characteristics of the fuel for the engine. If necessary, obtain a fuel analysis in order to confirm that the correct fuel is being used for the engine.
Fuel
Result: The fuel quality is OK.
Proceed to Test Step 3.
Result: The fuel quality is NOT OK.
Repair: Replace the fuel.
Verify that the repair eliminated the problem.
3. Check the Fuel Injectors
A. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
B. Access the "Cylinder Cutout Test" in the "Diagnostic Tests" under the "Diagnostics" menu.
C. Perform the "Automatic Cylinder Cutout Test" on Cat ET.
Injector Solenoid Test or Cylinder Cutout Test
Result: The test was successful.
Proceed to Test Step 4.
Result: The test was not successful.
Repair: Diagnose the problem and then repair the problem.
Reset all active codes and clear all logged codes.
Verify that the repair eliminated the problem.
4. Check for Lack of Lubrication
A. Check for proper lubrication of the valve components. Check for sufficient lubrication between the injector tappets and the rocker arms.
B. Check for blocked oil passages. Oil passages must be clean. Clean any oil passages that are questionable. Refer to the Disassembly and Assembly for additional information.
Lubrication
Result: The oil passages are not blocked and the engine has proper lubrication.
Proceed to Test Step 5.
Result: The oil passages are blocked or the engine does not have proper lubrication.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
5. Inspect the Valve Train Components
A. Check the valve lash. Refer to Troubleshooting, "Valve Lash Is Excessive".
B. Check for damage to valve train components. Remove the valve cover from the suspect cylinders. Check the following items for damage:
- Camshaft
- Valve rotocoil
- Valve springs
- Camshaft followers
- Rocker shaft
- Bridges
- Pushrods
- Injectors
Refer to the Disassembly and Assembly for additional information.
C. Check for valves that do not move freely. Remove the cylinder head and inspect the valves.
Refer to the Disassembly and Assembly for additional information.
Valve Train
Result: The valve train components are not damaged.
Proceed to Test Step 6.
Result: The valve train components are damaged.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
6. Inspect Gear Train and Components of the Lower End
Gear Train
Result: The gear train or lower end components are damaged.
Repair: Replace any damaged parts.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts engine EVINRUDE:

0282664
 
0282664 ENGINE COVER ASSY.
E20CRCDC, E25ECDR
0282667
 
0282667 ENGINE COVER ASSY.
E20CRCDC, E25ECDR
0282665
 
0282665 ENGINE COVER ASSY.
E20CRCDC, E25ECDR
0396175
0396178
 
0396178 ENGINE COVER ASSY.
E20CRCDC, E25ECDR
0396176
0396177
 
0396177 ENGINE COVER ASSY.
E20CRCDC, E25ECDR
0396983
 
0396983 ENGINE COVER, Lower
E20CRCCA, E20CRCDC, E20CRCUR, E25ECCM, E25ECDR, E25ECUA, E30ECCE, E30ECDM, E30ECUB, E35RCCE, E35RCDM, E35RCUB
Back to top