0283875 EVINRUDE ENGINE COVER ASSY.


0283875 ENGINE COVER ASSY. EVINRUDE E20CREND, E20CRERC, E20CRETS, E25REND, E25RERC, E25RETS, E30RENR, E30RERM, E30RETA, E35RENR, E35RERM, E35RETA ENGINE
0283875 ENGINE COVER ASSY. EVINRUDE
Rating:
93

Buy ENGINE COVER ASSY. 0283875 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

E20CREND, E20CRLEND, TE20CREND, TE20CRLEND 1992
E20CRERC, E20CRLERC 1994
E20CRETS, E20CRLETS, TE20CRETS, TE20CRLETS 1993
E25REND, E25RLEND 1992
E25RERC, E25RLERC 1994
E25RETS, E25RLETS 1993
E30RENR, E30RLENR 1992
E30RERM, E30RLERM 1994
E30RETA, E30RLETA 1993
E35RENR, E35RLENR 1992
E35RERM, E35RLERM 1994
E35RETA, E35RLETA 1993

Information:

1. Remove six bolts (1), two top bolts (2), housing (3) and the gasket. 2. Remove governor spring (4), the two wave washers, one flatwasher and seat (5) from the guide in the housing. 3. Remove bolts (6), cover (7) and the gasket from the housing. Use tooling (A) to remove seal (8) from the cover. 4. Remove low idle adjustment screw (9) and spring (10) from the housing. 5. Remove shaft assembly (11), lever (12) and lever (13) from the housing. 6. Remove two snap rings from pins (15) and remove pins (15). Remove plates (14) and stop (16) from the shaft assembly. 7. Remove pin (18), pin (17) and spring (19) from the shaft assembly. 8. Remove shaft (20) and lever (21) for the housing.
Remove check valve (22) only if a replacement is necessary because the check valve will be damaged during removal.
9. Remove check valve (22) if a replacement is necessary. 10. Remove contact (23) and body (24) for the governor dashpot adjustment screw from the housing. Remove bolts (25), cover (26) and the gasket from the housing. 11. Remove seal (27) from the spring guide. After seal (27) is removed, the snap ring and bearing can be removed from the spring guide. Remove high idle adjustment screw (28) only if a replacement is necessary. 12. If a replacement of the spring guide is necessary, use tooling (A) to remove the spring guide from housing (3). 13. Remove two bolts (29), housing (30) and the gasket from the fuel injection pump housing. 14. Remove bolts (31) and block (32) for the full load stop from the housing. 15. Remove bolts (33) and torque control group (34) from the block.16. Disassemble the torque control group and inspect the spacer, spring and insulator for damage or wear. 17. Remove the bolt that holds collar (35) to bolt (37). Remove collar (35) and spring (36) from bolt (37). Remove bolt (37) from the block.18. Remove the stop screws from collar (35) only if a replacement is necessary. 19. Remove bolts (39) and governor servo (38) from the fuel injection pump housing. 20. Remove lockring (44), seat (43), spring (broken link spring) (42) and sleeve (41) from valve (40). Remove the other lockring (44) from the groove in the center of valve (40). 21. Remove valve (40), sleeve (45) and piston (47) from the governor servo. Remove the O-ring seal from sleeve (45).22. Remove pin (46) and lever (48) from the governor servo. 23. Use tool (B) to hold spring (50) in compression so ring (49) can be removed. Spring (50) is used to put a preload on the thrust bearing for the camshaft in the fuel injection pump housing.24. Remove ring (49) then remove tool (B). 25. Remove bearing (51), sleeves (52) and spring (50) from the governor shaft. 26. Remove ring (53) and dashpot assembly (54) from the governor shaft. 27. Use tool (C) to remove snap ring (60) from seat (57). Remove ring (59) and spool (58) from seat (57).28. Remove seat (57) from spring (56) and remove spring (56) from seat (55). 29. Remove spring (overfueling spring) (61) and riser (62) from the governor shaft. 30. Remove ring (63), races (64) and bearing (65) from the riser. 31. Use a screwdriver to remove shield (66) as shown. Make a replacement of shield (66) any time it is removed. 32. Remove bolts (67) and carrier (68) for the governor flyweights. 33. Remove dowels (69) and flyweights (71) from the carrier.34. Remove shaft (70) from the carrier. Remove the dowel from shaft (70). 35. Remove races (72) and bearing (73) from the camshaft in the fuel injection pump housing.Assemble Governor
Put clean oil on all parts before assembly. Be sure all oil passages are clear.1. Install one race (1), bearing (2) and the other race (1) on the camshaft in the fuel injection pump housing. 2. Put flyweights (3) in position on carrier (4) and lnstall the dowels to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.230 mm (.0004 to .0091 in.) end play. 3. Install dowel (5) in governor shaft (6) and install the governor shaft in the carrier as shown. 4. Put the carrier in position on the camshaft and install the bolts that hold the carrier in place. Make a replacement of shield (7) any time it is removed.5. Install shield (7) on the carrier and use tool (A) to push the shield against its seat. Use a hammer and punch to move the metal (stake) two places on the side of the shield 180° 5° apart next to the holes in the shield. 6. Install one race (9), bearing (10), the other race (9) and use tool (B) to install the ring on riser (8) as shown. 7. Install riser (8) and spring (overfueling spring) on the governor shaft as shown. 8. Assemble the dashpot as follows:a) Install spring (12) on seat (11) and install seat (13) in spring (12).b) Put spool (14) and spring (15) in position on seat (13) and use tool (B) to install snap ring (16) to hold them in place. 9. Install dashpot assembly (17) on the governor shaft as shown. 10. Install ring (21) in the lower groove in the governor shaft. Install one sleeve (20), spring (19), the other sleeve (20) and bearing (18) on the governor shaft as shown. Spring (19) is used to put a preload on the thrust bearing on the camshaft in the fuel injection pump housing. 11. Use tool (C) to hold spring (19) in compression and install ring (22) in the groove in the governor shaft. Remove tool (C). 12. Put lever (27) in position on governor servo (23) and install pin (24) to hold the lever in place. Use a hammer and chisel to move the metal (stake) four places 90° apart on the outside surface on both legs of the governor servo to hold pin (24) in place.13.


Parts engine EVINRUDE:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE30EECS, BE30EEDE, BE30EEUD, E20CREDA, E20CREIE, E20CRE
0284058
 
0284058 ENGINE COVER ASSY.
E20CREIE, E20CREND, E20CRETS, E25REIE, E25REND, E25RETS, E30REIC, E30RENR, E30RETA, E35REIC, E35RENR, E35RETA
0434554
ENGINE COVER ASSY.
0434554 ENGINE COVER ASSY.
E20CREIE, E20CREND, E20CRETS, E25REIE, E25REND, E25RETS, E30REIC, E30RENR, E30RETA, E35REIC, E35RENR, E35RETA
0284127
 
0284127 ENGINE COVER ASSY.
E20CREND, E20CRERC, E20CRETS, E25REND, E25RERC, E25RETS, E30RENR, E30RERM, E30RETA, E35RENR, E35RERM, E35RETA
0284026
ENGINE COVER ASSY.
0284026 ENGINE COVER ASSY.
E20CREND, E20CRERC, E20CRETS, E25REND, E25RERC, E25RETS, E30RENR, E30RERM, E30RETA, E35RENR, E35RERM, E35RETA
0283871
 
0283871 ENGINE COVER ASSY.
E20CREND, E20CRERC, E20CRETS, E25REND, E25RERC, E25RETS, E30RENR, E30RERM, E30RETA, E35RENR, E35RERM, E35RETA
0435149
 
0435149 ENGINE COVER ASSY.
E20CREDA, E20CREND, E20CREOR, E20CRERC, E20CRETS, E25REDA, E25REND, E25REOR, E25RERC, E25RETS, E30REDE, E30RENR, E30REOB, E30RERM, E30RETA, E35RENR, E35RERM, E35RETA, SE35REDE
0435154
 
0435154 ENGINE COVER ASSY.
BE20SREDA, BE25BAEDR, BE30BAEDE, E20CREDA, E20CREND, E20CREOR, E20CRERC, E20CRETS, E25REDA, E25REND, E25REOR, E25RERC, E25RETS, E30REDE, E30RENR, E30REOB, E30RERM, E30RETA, E35RENR, E35RERM, E35RETA, SE35REDE
Back to top