0284129 EVINRUDE ENGINE COVER ASSY.


0284129 ENGINE COVER ASSY. EVINRUDE E20EEND, E20EERC, E20EETS, E25EENS, E25EERR, E25EETC, E25TEEND, E25TEERC, E25TEETS, E30EENR, E30EERM, E30EETA, E30TEENR, E30TEERM, E30TEETA ENGINE
0284129 ENGINE COVER ASSY. EVINRUDE
Rating:
8

Buy ENGINE COVER ASSY. 0284129 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

E20EEND, E20ELEND 1992
E20EERC, E20ELERC 1994
E20EETS, E20ELETS 1993
E25EENS, E25ELENS, TE25ELENS, VE25ELENS 1992
E25EERR, E25ELERR 1994
E25EETC, E25ELETC, TE25ELETC, VE25ELETC 1993
E25TEEND, E25TELEND 1992
E25TEERC 1994
E25TEETS, E25TELETS 1993
E30EENR, E30ELENR, VE30EENR, VE30ELENR 1992
E30EERM, E30ELERM 1994
E30EETA, E30ELETA, VE30EETA, VE30ELETA 1993
E30TEENR, E30TELENR 1992
E30TEERM, E30TELERM 1994
E30TEETA, E30TELETA 1993

Information:

1. Turn the engine counterclockwise (as seen from the flywheel end of the engine) with Tool (A) until the No. 1 piston is at top center (TC) on the compression stroke. Install the timing bolt. Install 6V-2112 Timing Pin through the hole in the injection pump housing. See the topic "Finding Top Center Compression Position for NO. 1 Piston" in Testing & Adjusting. Tool (B), 6V-2112 Timing Pin, replaces 6V-6019 Timing Pin. 2. Remove two bolts (1).3. Remove eleven bolts (2) and cover (3). 4. Remove four bolts (5), retainer (6) and governor and fuel pump drive (4).Install Governor & Fuel Pump Drive
1. Install governor and fuel pump drive (4). Install retainer (6) and four bolts (5).2. Tighten the bolts (5) with fingers until there is a small amount of friction (slight drag) between the retainer and governor and fuel pump drive (4). This friction will hold the unit against the timing gears. This prevents play (backlash) when gears are turned to the correct position.3. Remove the timing bolt. Turn the flywheel until the timing pin will go into the groove in the injection pump camshaft.4. With the timing pin installed, turn the flywheel clockwise (opposite the direction of engine rotation) a minimum of 30 degrees. The reason for this step is to be sure the play is removed from the timing gears when the engine is put on top center (TC).5. Turn the flywheel in the direction of engine rotation until the No. 1 piston of the engine is on top center compression stroke. Then turn the timing bolt into the threaded hole in the flywheel.6. Tighten bolts (5) to 25 N m (20 lb ft). Then remove the timing pin from the injection pump housing.7. Tighten bolts (5) to 135 7 N m (100 5 lb ft). Then remove the timing bolt from the flywheel.8. Turn the crankshaft two complete revolutions and check the timing again to see that timing pin will go into the groove in the injection pump camshaft with bolt in flywheel.9. If the timing is not correct, do the procedure of Steps 1 through 7 again. If the timing is correct, be sure to remove the timing pin and the timing bolt. 5. Install eleven bolts (2) and cover (3).6. Install two bolts (1).Disassemble Governor & Fuel Pump Drive
Start By:a. remove governor and fuel pump drive 1. Remove flange assembly (1). 2. Remove two springs (2) and two weights (3) from drive gear assembly (4). 3. Remove two slides (5) from pistons (6).4. Separate drive gear assembly 94) from advance sleeve (7).Assemble Governor & Fuel Pump Drive
1. Put weights (3) in position in flange assembly (1) as shown.2. Install springs (2) in flange assembly (1). 4. Use 1P-008 General Purpose Lubricant to hold slides (5) in position on drive gear assembly (4). Install slides (5) on pistons (6).5. Install advance sleeve (7) to drive gear assembly (4). 6. Install drive gear assembly (4) on flange assembly (1). Make sure slides (5) fit in grooves of the weights.End By:a. install governor and fuel pump drive


Parts engine EVINRUDE:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE30EECS, BE30EEDE, BE30EEUD, E20CREDA, E20CREIE, E20CRE
0284059
 
0284059 ENGINE COVER ASSY.
E20EEIE, E20EEND, E20EETS, E25EEID, E25EENS, E25EETC, E30EEIC, E30EENR, E30EETA
0434555
 
0434555 ENGINE COVER ASSY.
E20EEIE, E20EEND, E20EETS, E25EEID, E25EENS, E25EETC, E30EEIC, E30EENR, E30EETA
0284128
 
0284128 ENGINE COVER ASSY.
E20EEND, E20EERC, E20EETS, E25EENS, E25EERR, E25EETC, E30EENR, E30EERM, E30EETA
0284130
 
0284130 ENGINE COVER ASSY.
E20EEND, E20EERC, E20EETS, E25EENS, E25EERR, E25EETC, E25TEEND, E25TEERC, E25TEETS, E30EENR, E30EERM, E30EETA, E30TEENR, E30TEERM, E30TEETA
0435150
ENGINE COVER ASSY.
0435150 ENGINE COVER ASSY.
E20EEND, E20EEOR, E20EERC, E20EETS, E25EENS, E25EEOA, E25EERR, E25EETC, E30EENR, E30EEOB, E30EERM, E30EETA
0435155
 
0435155 ENGINE COVER ASSY.
BE20SEEDA, BE25EEDM, BE30EEDE, E20EEND, E20EEOR, E20EERC, E20EETS, E25EENS, E25EEOA, E25EERR, E25EETC, E25TEEDA, E25TEEND, E25TEEOR, E25TEERC, E25TEETS, E30EENR, E30EEOB, E30EERM, E30EETA, E30TEEDE, E30TEENR, E30TEEOB, E30TEERM, E30TEETA
0435152
ENGINE COVER ASSY.
0435152 ENGINE COVER ASSY.
BE20SEEDA, BE25EEDM, BE30EEDE, E20EEND, E20EEOR, E20EERC, E20EETS, E25EENS, E25EEOA, E25EERR, E25EETC, E25TEEDA, E25TEEND, E25TEEOR, E25TEERC, E25TEETS, E30EENR, E30EEOB, E30EERM, E30EETA, E30TEEDE, E30TEENR, E30TEEOB, E30TEERM, E30TEETA
Back to top