0284715 EVINRUDE ENGINE COVER ASSY.


0284715 ENGINE COVER ASSY. EVINRUDE BE20SEEDA, BE20SEEUM, BE25EEDM, BE25EEUB, BE30EEDE, BE30EEUD, E20EEOR, E25EEOA, E25TEEDA, E25TEEOR, E25TEEUM, E30EEOB, E30TEEDE, E30TEEOB, E30TEEUD ENGINE
0284715 ENGINE COVER ASSY. EVINRUDE
Rating:
33

Buy ENGINE COVER ASSY. 0284715 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

BE20SEEDA, BE20SELEDA 1996
BE20SEEUM, BE20SELEUM 1997
BE25EEDM, BE25ELEDM, BE25EREDC, BE25ERLEDC, E25EEDM, E25ELEDM 1996
BE25EEUB, BE25ELEUB, E25EEUB, E25ELEUB 1997
BE30EEDE, BE30ELEDE, E30EEDE, E30ELEDE 1996
BE30EEUD, BE30ELEUD, E30EEUD, E30ELEUD 1997
E20EEOR, E20ELEOR 1995
E25EEOA, E25ELEOA 1995
E25TEEDA, E25TELEDA, HE25TELEDA 1996
E25TEEOR, E25TELEOR 1995
E25TEEUM, E25TELEUM 1997
E30EEOB, E30ELEOB 1995
E30TEEDE, E30TELEDE 1996
E30TEEOB, E30TELEOB 1995
E30TEEUD, E30TELEUD 1997

Information:

1. Disconnect tube assembly (1) at the fitting in the cylinder block.2. Remove bolts (2) that hold the flywheel housing to the cylinder block. 3. Install tooling (A) on each side of the flywheel housing (3). Use washers as needed to make tooling (A) straight. Fasten a hoist to tooling (A).4. Remove bolt (4) that holds the shaft in place.5. Remove bolts (5) that hold the flywheel housing to the cylinder block. Remove flywheel housing (3). The weight is 115 lb. (52 kg).Install Flywheel Housing
1. Thoroughly clean the contact surfaces of the cylinder block and flywheel housing. Install a new gasket on the cylinder block.2. Install two 1/2"-13 NC guide pins 180° apart in the cylinder block. 3. Install tooling (A) on each side of the flywheel housing. Use washers as needed to make tooling (A) straight. Fasten a hoist.4. Put flywheel housing (1) in position on the cylinder block. 5. Install the bolts that hold the flywheel housing to the cylinder block. Tighten bolts 1 through 8 in number sequence to a torque of 100 11 lb.ft. (135 15 N m). Tighten bolts 9 through 17 in number sequence to a torque of 41 5 lb.ft. (55 7 N m). Tighten bolts 1 through 8 in number sequence again to a torque of 100 11 lb.ft. (135 15 N m). Tighten bolts 9 through 17 in number sequence again to a torque of 41 5 lb.ft. (55 7 N m).6. Install the bolt that holds shaft (2) in place to the cylinder block. Tighten the bolt to a torque of 100 10 lb.ft. (135 14 N m). 7. Connect tube assembly (3).end by:a) install oil panb) install electric starting motorc) install flywheelDisassemble Flywheel Housing
start by:a) remove flywheel housing 1. Remove the bolts and nuts that hold adapter (1) in place. Remove adapter (1). 2. Remove bearing cup (2) from adapter (1). Remove O-ring seal (3). 3. Remove gear assembly (4) from the flywheel housing. 4. Remove bearing cone (5) from each side of the gear assembly with tooling (A). 5. Remove bearing cup (6) from the flywheel housing. 6. Remove the bolt from shaft (7). Remove shaft (7) with tooling (B).7. Remove the O-ring seals from the shaft. 8. Remove gear assembly (8) from the flywheel housing. 9. Remove bearing cone (9), spacer (10) and bearing cone (12) from gear (11). 10. Remove bearing cup (13), spacer (14) and bearing cup (15) from gear (11). Remove the ring from gear (11).Assemble Flywheel Housing
1. Inspect the O-ring seals and ports for damage and make replacements if needed. 2. Install the ring in gear (1). Install spacer (2) in the gear.3. Lower the temperature of bearing cups (3) and (4). Install bearing cup (3) and (4) in the gear. 4. Install bearing cone (7), spacer (6) and bearing cone (5) in gear (1). 5. Install gear assembly (8) in the flywheel housing. 6. Install O-ring seals (9) on shaft (10). Put clean oil on the seals. Make an alignment of the holes in the shaft with the holes in the flywheel housing and install shaft (10). Install one of the bolts to a torque of 100 10 lb.ft. (135 14 N m). 7. Lower the temperature of bearing cup (11). Install bearing cup (11). 8. Heat bearing cones (12) to a maximum temperature of 275°F (135°C). Install bearing cones (12) on gear (13). 9. Install gear assembly (14) in the flywheel housing. 10. Lower the temperature of bearing cone (15). Install bearing cone (15) in adapter (17).11. Install O-ring seal (16) on adapter (17). Put clean oil on the O-ring seal. 12. Install adapter (17) on the flywheel housing.end by:a) install flywheel housing


Parts engine EVINRUDE:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE30EECS, BE30EEDE, BE30EEUD, E20CREDA, E20CREIE, E20CRE
0435152
ENGINE COVER ASSY.
0435152 ENGINE COVER ASSY.
BE20SEEDA, BE25EEDM, BE30EEDE, E20EEND, E20EEOR, E20EERC, E20EETS, E25EENS, E25EEOA, E25EERR, E25EETC, E25TEEDA, E25TEEND, E25TEEOR, E25TEERC, E25TEETS, E30EENR, E30EEOB, E30EERM, E30EETA, E30TEEDE, E30TEENR, E30TEEOB, E30TEERM, E30TEETA
0284714
 
0284714 ENGINE COVER ASSY.
BE20SEEDA, BE20SEEUM, BE25EEDM, BE25EEUB, BE30EEDE, BE30EEUD, E20EEOR, E25EEOA, E25TEEDA, E25TEEOR, E25TEEUM, E30EEOB, E30TEEDE, E30TEEOB, E30TEEUD
0284713
 
0284713 ENGINE COVER ASSY.
BE20SEEDA, BE20SEEUM, BE25EEDM, BE25EEUB, BE30EEDE, BE30EEUD, E20EEOR, E25EEOA, E30EEOB
0284396
 
0284396 ENGINE COVER ASSY.
E20EEOR, E25EEOA, E30EEOB
0284133
 
0284133 ENGINE COVER ASSY.
E20EEOR, E25EEOA, E30EEOB
0437188
 
0437188 ENGINE COVER ASSY.
BE20SEEDA, BE25EEDM, BE30EEDE, E20EEOR, E25EEOA, E25TEEDA, E25TEEOR, E30EEOB, E30TEEDE, E30TEEOB
0438331
 
0438331 ENGINE COVER ASSY.
BE20SEECB, BE20SEEUM, BE25EECE, BE25EEUB, BE30EECS, BE30EEUD
Back to top