0284793 EVINRUDE ENGINE COVER, Ev., all 6 hp


0284793 ENGINE COVER, Ev., all 6 hp EVINRUDE BE5DREDS, BE5DREUC, BE6DREDS, BE6DREUC, BE8REDS, E6REOD, E8REOD, E8REUC ENGINE
0284793 ENGINE COVER, Ev., all 6 hp EVINRUDE
Rating:
43

Buy ENGINE COVER, Ev., all 6 hp 0284793 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

BE5DREDS, BE5DRLEDS 1996
BE5DREUC, BE5DRLEUC 1997
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E6REOD, E6RLEOD, E6SLEOD 1995
E8REOD, E8RLEOD, E8SRLEOD 1995
E8REUC, E8RLEUC, E8SRLEUC 1997

Information:

1. Loosen the bolts (2) that hold main bearing caps (1) to cylinder block.2. Install one of the bolts for flywheel in each end of the crankshaft. 3. Fasten a hoist and remove the main bearing caps. Remove bearings from bearing caps.4. Remove crankshaft from engine. Weight is 350 lb. (159 kg).5. Remove crankshaft main bearings from cylinder block. If new main bearings are not to be installed, keep old bearings with identification as to their location in cylinder block. 6. Use tooling (A) to remove crankshaft outer gear. Use a hammer and a chisel to remove spacer. 7. Use tooling (B) to remove dowel.8. Use tooling (A) to remove crankshaft inner gear.Install Crankshaft
1. Heat the crankshaft gears to maximum temperature of 400° F (204° C). 2. Install crankshaft inner gear (2) on crankshaft.3. Install spacer on crankshaft.4. Install the pin in end of crankshaft. The pin must be extended no more than .19 in. (4.82 mm) from surface of crankshaft.5. Install the crankshaft outer gear (1) on crankshaft. The pin in crankshaft must be in alignment with notch in crankshaft gear (1).6. Clean the cylinder block and main bearing caps thoroughly. 7. Install upper half of main bearings (3) in the block. Put clean engine oil on the bearings and journals of crankshaft.8. Install one bolt for flywheel on each end of crankshaft. 9. Fasten a hoist and put crankshaft in position in block. Be sure the "V" mark on camshaft gear is in alignment with "V" mark on crankshaft gear.10. Install main bearings in bearing caps. Be sure the tabs (4) on back of bearings fit in the grooves of caps and cylinder block.11. Use wire (B) to check bearing clearance.12. Put wire (B) on the bearing. Be sure main bearing caps (5) are installed so the numbers on the side of the cylinder block are the same as the numbers on the bearing caps, and the arrows on the caps are toward the front of the cylinder block. 13. Install the main bearing caps. Install the bolts (6) and tighten the bolts, at end with tab first, to a torque of 190 10 lb.ft. (26.2 1.4 mkg). Put a mark on the bolts and caps. Turn the bolts at opposite end of tab first an extra 120° 5° from the mark.14. Remove the main bearing caps. Remove wire (B) from the caps. Check the thickness of wire (B) to find the bearing clearance. The bearing clearance must be .0037 to .0068 in. (0.093 to 0.172 mm) with new bearings. Maximum clearance with used bearings is .010 in. (0.35 mm).15. Install the thrust bearings for No. 4 main bearing. Install the thrust bearings with the side marked "BLOCK SIDE" toward the cylinder block.16. Put clean engine oil on the threads of the bolts. Install the main bearing caps. Install the bolts and the bolts, at the end with the tab first, to a torque of 190 10 lb.ft. (26.2 1.4 mkg). Put a mark on the bolts and caps. Turn the bolts, opposite end of tab first, an extra 120° 5° from the mark.17. Check the end play of the crankshaft with tool group (A). Be sure the dial indicator is against a machined surface. The end play is controlled by the thrust bearings of No. 4 (center) main. The end play with new bearings must be .006 to .020 in. (0.152 to 0.508 mm). The maximum permissible end play with used bearings is .035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install crankshaft front seal wear sleevee) install crankshaft rear seal wear sleevef) install fuel injection pump housing and governor


Parts engine EVINRUDE:

0435144
 
0435144 ENGINE COVER, Jo., 8SRL
BE5DREDS, BE6DREDS, BE8REDS, E6RENM, E6REOD, E6RERE, E6RETB, E8RENM, E8REOD, E8RERE, E8RETB
0435141
 
0435141 ENGINE COVER, Jo., 6R
BE5DREDS, BE6DREDS, BE8REDS, E6RENM, E6REOD, E6RERE, E6RETB, E8RENM, E8REOD, E8RERE, E8RETB
0435143
 
0435143 ENGINE COVER, Jo., 8R
BE5DREDS, BE6DREDS, BE8REDS, E6RENM, E6REOD, E6RERE, E6RETB, E8RENM, E8REOD, E8RERE, E8RETB
0284794
 
0284794 ENGINE COVER, Ev., all 8 hp
BE5DREDS, BE5DREUC, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8REDS, E6REOD, E8REOD, E8REUC
0437618
 
0437618 ENGINE COVER, Jo., all 8 hp
BE5DREDS, BE6DREDS, BE8REDS, E6REOD, E8REOD
0437617
 
0437617 ENGINE COVER, Jo., 6R, 6RL, 6SL
BE5DREDS, BE6DREDS, BE8REDS, E6REOD, E8REOD
0284694
 
0284694 ENGINE COVER, Ev., 5DR
BE5DREDS, BE5DREUC, BE6DREDS, BE6DREUC, BE8REDS, E6REOD, E8REOD, E8REUC
0435140
 
0435140 ENGINE COVER, Jo., 5DR
BE5DREDS, BE6DREDS, BE8REDS, E6REOD, E8REOD
Back to top