0285275 ENGINE COVER ASSY. EVINRUDE
E200WPXEEN, E200WPXSSC
ENGINE
Price: query
Rating:
Compatible models:
E200WPXEEN
E200WPXSSC
EVINRUDE
BRP EVINRUDE entire parts catalog list:
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1 Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (A) to turn the flywheel in order to access the connecting rod cap that will be removed.
Illustration 1 g00913801Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.
Remove bolts (1) and connecting rod cap (2) from the crankshaft.
Push the connecting rod away from the crankshaft. Remove the upper half of the connecting rod bearing.Note: Be careful not to damage the cylinder liner or the crankshaft journal.
Remove the lower half of the connecting rod bearing from connecting rod cap (2).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B Loctite Moly 50 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Illustration 2 g00913801
Illustration 3 g03746219
Section view of connecting rod showing torque sequence. Chamfer (3) and dowel (4) can be used to reference orientation.
Install the upper half of the connecting rod bearing on the connecting rod . Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod. Coat the connecting rod bearing with clean engine oil. Position the connecting rod onto a journal of the crankshaft.
Install the lower half of the connecting rod bearing on connecting rod cap (2). Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod cap. Coat the connecting rod bearing with clean engine oil.Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod. Install the chamfered side of the connecting rod cap next to the thrust surface of the crankshaft.
Apply Tooling (B) to the threads, the shank, and the seat of bolts (1).
Place connecting rod cap (2) into position. Install bolts (1). Use the following procedure to tighten the bolts:
Tighten Bolt (A) and Bolt (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) again to a torque of 90 5 N m (65 4 lb ft).
Place an index mark on the bolts and the connecting rod cap. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the engine oil pump.
Parts engine EVINRUDE:
0437146
0437146 ENGINE COVER & SEAL ASSY., Stbd.
BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, E200CXEOC, E200WPXEEN, E225CXEOB, E250CXECD, SE200WTPLA, SE200WTPLG, SE200WTPLS
0586243
0586243 ENGINE CABLE ASSY.
BE200CXECM, BE225CXECS, E200WPXEEN, E200WPXSIF, E200WPXSSC, E250CXECD, SE200WTPLG
0285076
0439773
0439773 ENGINE COVER & SEAL ASSY., Stbd.
E200FCSSSC, E200FCXEEN, E200FCXSIF, E200FPLSSC, E200FPXSSC, E200WPXEEN, E200WPXSIF, E200WPXSSC, E225FCXEEN, E225FCXSIF, E225FCXSSC, E225FGLSSC, E225FHLSSS, E225FPLSIF, E225FPXSSC, E250FCXSIF, E250FCXSSS, E250FGLSSS, E250FPXSSS
0344806
0344806 ENGINE COVER, Port
E200FCSSSC, E200FCXEEN, E200FCXSIF, E200FPLSSC, E200FPXSSC, E200WPXEEN, E200WPXSIF, E200WPXSSC, E225FCXEEN, E225FCXSIF, E225FCXSSC, E225FGLSSC, E225FHLSSS, E225FPLSIF, E225FPXSSC, E250FCXSIF, E250FCXSSS, E250FGLSSS, E250FPXSSS
5000571
5001407