0435181 EVINRUDE ENGINE COVER ASSY., 200STL, VJ200SL


0435181 ENGINE COVER ASSY., 200STL, VJ200SL EVINRUDE E185ESXENR, E200CXENE, E225CXENR ENGINE
0435181 ENGINE COVER ASSY., 200STL, VJ200SL EVINRUDE
Rating:
58

Buy ENGINE COVER ASSY., 200STL, VJ200SL 0435181 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E185ESXENR 1992
E200CXENE, E200STLENS, E200TXENE, VE200SLENS, VE200TXENE 1992
E225CXENR, E225PLENR, E225PXENR, E225TLENR, E225TXENR, VE225PLENR, VE225PXENR, VE225TLENR, VE225TXENR 1992

Information:

1. Remove the covers and gaskets over camshaft gears (3).2. Remove cover (1) from the top of the flywheel housing.3. Remove bolts (2) and the plate and adapter that fasten the camshaft gears to the camshaft.4. Put the three washers from tooling (A) behind plate (5) and install the bolt and plate (5).
Do not apply more than 51675 kPa (7500 psi) pressure to 1P820 Hydraulic Puller. 8B7559 adapters are rated at 6 1/2 ton each and 1P820 Hydraulic Puller is rated at 17 ton at 68900 kPa (10000 psi). If to much pressure is applied, the gear may be damaged.
5. Install tooling (A) on camshaft drive gear (3). Apply 51,675 kPa (7500 psi) to the puller and hit the screw part of the puller with a hammer until the gear is free of the camshaft taper. Remove tooling (A) and gear (3).6. Put stands or blocks under the rear of the engine block. The weight of the engine is approximately 6090 kg (13,400 lb.).7. Install tooling (B) on the top of the flywheel housing and attach a hoist.8. Remove all bolts that fasten the flywheel housing to the engine block. Be aware that there are two bolts below cover (1), and the two bolts that pass through shaft (4) must also be removed.9. Remove the flywheel housing from the engine. The weight of the flywheel housing is 210 kg (454 lb.).Install Flywheel Housing
1. Use 6V1541 Quick Cure primer to clean the mating surfaces of the flywheel housing and the cylinder block. Put 6V6640 Gasket Maker on the surfaces of the flywheel housing that make contact with the cylinder block.2. Install tooling (A) on the top of the flywheel housing. Fasten a hoist and put the flywheel housing in position on the cylinder block. 3. Install the bolts in their respective locations. See the Installation Chart. Tighten the 1/2" - NC bolts to a torque of 135 15 N m (100 11 lb. ft.). Tighten the 5/8" NC bolts to a torque of 270 25 N m (200 18 lb. ft.). 4. Put the camshaft timing pins in position and put the timing bolt in the flywheel with number 1 piston at the compression stroke. See the topic, Install Camshafts in this module. Be sure gear backlash is removed.5. Install camshaft gears (2), tach drive adapter (4), plate (1) and bolts (3). Tighten bolts (3) as follows:a. Tighten bolts (3) to a torque of 360 50 N m (265 35 lb. ft.).b. Hit bolts (3) with a soft hammer to seat the gear on the camshaft.c. Tighten bolts (3) again to a torque of 360 50 N m (265 35 lb. ft.).d. Repeat Steps b and c until the torque does not change.6. Remove the timing pins from the camshafts and the flywheel.7. Install the cover on the top of the flywheel housing and the covers over both camshaft drive gears. Two bolts, that fasten each camshaft gear cover to the flywheel housing, are longer and must be installed at locations (X).END BY:a. install crankshaft rear seal and wear sleeveb. install oil pan, (rear half only)c. install electric starting motorsd. install enginee. install tach drive


Parts engine EVINRUDE:

0432783
 
0432783 ENGINE COVER & SEAL ASSY., Stbd.
E185ESXENR, E185ESXESS, E185ESXW, E200CXCEA, E200CXEIB, E200CXENE, E200CXESM, E225CXCED, E225CXEIC, E225CXENR, E225CXESS
0434390
ENGINE COVER, Port
0434390 ENGINE COVER, Port
BE130TLECE, BE130TLEDM, BE130TLEUB, E120TLEIE, E120TLEND, E120TLERC, E120TLETF, E125ESXENR, E125ESXERK, E125ESXETA, E125WTPLE, E130CXAOR, E140CXARC, E140CXATF, E140CXEIA, E140CXENM, E185ESXENR, E200CXEIB, E200CXENE, E225CXEIC, E225CXENR, SE125RWYJ, S
0284171
 
0284171 ENGINE COVER ASSY., 185
E185ESXENR, E200CXENE, E225CXENR
0284116
 
0284116 ENGINE COVER ASSY., 200STL, VE200SL
E185ESXENR, E200CXENE, E225CXENR
0284102
 
0284102 ENGINE COVER ASSY., 225TL
E185ESXENR, E200CXENE, E225CXENR
0284201
 
0284201 ENGINE COVER ASSY., 200CX
E185ESXENR, E200CXENE, E225CXENR
0284103
 
0284103 ENGINE COVER ASSY., 225PL
E185ESXENR, E200CXENE, E225CXENR
0284204
 
0284204 ENGINE COVER ASSY., 225PX
E185ESXENR, E200CXENE, E225CXENR
Back to top