0321493 EVINRUDE EXHAUST HOUSING, Outer


0321493 EXHAUST HOUSING, Outer EVINRUDE 70873C, 70973R, E70ELCIH, E70ELCNB, E70ELCRD, E70ELCSA, E70ELCTE, E75ECRD, E75ERCIH, E75ERCNB, E75ERCSA, E75ERCTE EXHAUST
0321493 EXHAUST HOUSING, Outer EVINRUDE
Rating:
63

Buy EXHAUST HOUSING, Outer 0321493 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

BRP EVINRUDE entire parts catalog list:

70873C, 75842C, 75843C 1978
70973R, 75942R, 75943R 1979
E70ELCIH, E70ELCIM, E70TLCIM 1981
E70ELCNB, E70TLCNB 1982
E70ELCRD, E70TLCRD 1984
E70ELCSA 1980
E70ELCTE, E70TLCTE 1983
E75ECRD, E75ELCRD, E75TLCRD 1984
E75ERCIH, E75ERCIM, E75ERLCIH, E75ERLCIM, E75TRLCIH, E75TRLCIM 1981
E75ERCNB, E75ERLCNB, E75TRLCNB 1982
E75ERCSA, E75ERLCSA, E75TRLCSA 1980
E75ERCTE, E75ERLCTE, E75TRLCTE 1983

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03346212
Slide locking tab (1) into the unlocked position. Disconnect harness assembly (2) from pressure sensor (3).
Compress hose clamp (6) and slide the hose clamp along hose assembly (8). Disconnect the hose assembly from pressure sensor (3).
Compress hose clamp (7) and slide the hose clamp along hose assembly (9). Disconnect the hose assembly from pressure sensor (3).
Remove bolts (4) from pressure sensor (3).
Remove pressure sensor (3) from bracket (5).
Illustration 2 g03346220
If necessary, follow Step 6.a through Step 6.f in order to remove and disassemble tube assembly (14) and tube assembly (18).
Remove banjo bolt (11) from tube assembly (14). Remove sealing washers (12) (not shown).
Remove banjo bolt (16) from tube assembly (18). Remove sealing washers (17) (not shown).
Remove tube assembly (14) and tube assembly (18) from the Diesel Particulate Filter (DPF).
If necessary, remove nut and bolt (15) from the clamp for tube assembly (14) and tube assembly (18). Note: Make temporary marks on the clamp and the tube assemblies for assembly purposes.
If necessary, compress hose clamp (10) and slide the hose clamp along hose assembly (8). Disconnect the hose assembly from tube assembly (18).
If necessary, compress hose clamp (13) and slide the hose clamp along hose assembly (9). Disconnect the hose assembly from tube assembly (14). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the pressure sensor is free from wear or damage. Replace any components that are not free from wear or damage.
Ensure that the tube assemblies are free from wear, damage, and restriction. Replace any components that are not free from wear, damage, or restriction.
Illustration 3 g03346220
If necessary, follow Step 3.a through Step 3.h in order to install and assemble tube assembly (14) and tube assembly (18).
If necessary, connect hose assembly (8) to tube assembly (18). Compress hose clamp (10) and slide the hose clamp along hose assembly (8). Ensure that the hose clamp is correctly positioned.
If necessary, connect hose assembly (9) to tube assembly (14). Compress hose clamp (13) and slide the hose clamp along hose assembly (9). Ensure that the hose clamp is correctly positioned.
If necessary, position the clamp onto tube assembly (14) and tube assembly (18). Install nut and bolt (15) to the clamp hand tight. Note: Ensure that the clamp is correctly positioned onto tube assemblies.
Position tube assembly (14) and tube assembly (18) onto the Diesel Particulate Filter (DPF).
Install a new sealing washer (12) (not shown) onto banjo bolt (11). Install banjo bolt (11) to tube assembly (14) and install remaining sealing washer (12) (not shown). Tighten banjo bolt (11) finger tight.
Install a new sealing washer (17) (not shown) onto banjo bolt (16). Install banjo bolt (16) to tube assembly (18) and install remaining sealing washer (17) (not shown). Tighten banjo bolt (16) finger tight.
Tighten the nut and bolt (15) to a torque of 10 N m (89 lb in).
Tighten banjo bolt (11) and banjo bolt (16) to a torque of 25 N m (221 lb in). Ensure that the tube assemblies are not strained as the banjo bolts are tightened.
Illustration 4 g03346212
Position pressure sensor (3) onto bracket (5).
Install bolts (4) to pressure sensor (3).
Tighten bolts (4) to a torque of 10 N m (89 lb in).
Connect hose assembly (9) to pressure sensor (3). Compress hose clamp (7) and slide the hose clamp along hose assembly (8). Ensure that the hose clamp is correctly positioned.
Connect hose assembly (8) to pressure sensor (3). Compress hose clamp (6) and slide the hose clamp along hose assembly (8). Ensure that the hose clamp is correctly positioned.
Connect harness assembly (2) to pressure sensor (3). Slide locking tab (1) into the locked position.
Compress hose clamp (7) and slide the hose clamp along hose assembly . Disconnect the hose assembly from pressure sensor (3).


Parts exhaust EVINRUDE:

0319266
 
0319266 EXHAUST HOUSING, Inner
70442M, 70572B, 70773S, 70873C, 70973R, 75542B, 75642D, E60ELCDS, E60ELCUC, E70ELCIH, E70ELCNB, E70ELCOS, E70ELCRD, E70ELCSA, E70ELCTE, E75ECCA, E75ECDC, E75ECOS, E75ECRD, E75ECUR, E75ERCIH, E75ERCNB, E75ERCSA, E75ERCTE
0319079
 
0319079 EXHAUST HOUSING, Inner
70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D
0320211
 
0320211 EXHAUST HOUSING,Outer
70773S, 70873C, 70973R, 75542B, 75642D, E60ELCDS, E60ELCUC, E70ELCIH, E70ELCNB, E70ELCOS, E70ELCRD, E70ELCSA, E70ELCTE, E75ECCA, E75ECDC, E75ECOS, E75ECRD, E75ECUR, E75ERCIH, E75ERCNB, E75ERCSA, E75ERCTE
0323715
 
0323715 EXHAUST HOUSING
70973R, E70ELCIH, E70ELCNB, E70ELCRD, E70ELCSA, E70ELCTE, E75ECRD, E75ERCIH, E75ERCNB, E75ERCSA, E75ERCTE
Back to top