0333657 EVINRUDE EXHAUST HOUSING, Inner


0333657 EXHAUST HOUSING, Inner EVINRUDE BE250CXECB, BE250CXEDA, BE250CXEUM, E250CXARC, E250CXATF, E250CXEIE, E250CXEND, E250CXEOR, E275CXCCA, E300CXCCA, E300CXCEM, E300CXEIE, E300CXEND, E300CXEOR, E300CXERC, E300CXESB, E300CXETF EXHAUST
0333657 EXHAUST HOUSING, Inner EVINRUDE
Rating:
13

Buy EXHAUST HOUSING, Inner 0333657 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

BRP EVINRUDE entire parts catalog list:

BE250CXECB, BE250TXECB 1998
BE250CXEDA, BE250TXEDA 1996
BE250CXEUM, BE250TXEUM 1997
E250CXARC, E250CXERC, E250CZERC, E250TXARC, E250TXERC, E250TZERC 1994
E250CXATF, E250CXATS, E250CXETF, E250CXETS, E250CZATF, E250CZATS, E250CZETF, E250CZETS, E250TXATF, E250TXATS, E250TXETF, E250TXETS, E250TZATF, E250TZATS, E250TZETF, E250TZETS 1993
E250CXEIE, E250TXEIE 1991
E250CXEND, E250CZEND, E250TXEND, E250TZEND 1992
E250CXEOR, E250CZEOR, E250TXEOR, E250TZEOR 1995
E275CXCCA, E275PLCCA, E275PXCCA 1988
E300CXCCA, E300PLCCA, E300PXCCA 1988
E300CXCEM, E300PLCEM, E300PXCEM 1989
E300CXEIE, E300PLEIE, E300PXEIE 1991
E300CXEND, E300PLEND, E300PXEND 1992
E300CXEOR, E300PLEOR, E300PXEOR 1995
E300CXERC, E300PLERC, E300PXERC 1994
E300CXESB, E300PLESB, E300PXESB 1990
E300CXETF, E300CXETS, E300PLETF, E300PLETS, E300PXETF, E300PXETS 1993

Information:


Table 1
J1939 Code and Description Comments
1208-13
Engine Pre-filter Oil Pressure : Out of Calibration During the last calibration attempt, a problem has been detected.
The code is logged.
During a manual calibration, the pressure offset value is set to 0 kPa (0 psi).
During an automatic calibration, the pressure offset value is set to the previous calibration value.
2452-13
Generator Total Real Power : Out of Calibration The diagnostic will be active when using a secondary generator power sensor and the values between the PWM and analog signal differ by more than 100 kW.
4817-13
Engine Intake Manifold #1 Absolute Pressure : Out of Calibration During key on, the signal voltage from the Intake Manifold pressure sensor indicated an Intake Manifold pressure greater than +/- 15 kPa (2.2 psi) from the Atmospheric Pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
5631-13
Engine Throttle Valve Differential Pressure : Out of Calibration During Key on, the signal voltage from the engine throttle valve differential pressure sensor indicated that the differential pressure detected is greater than 11 kPa (1.6 psi)
There is not a reference for this sensor.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Establish communication between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before troubleshooting or clearing diagnostic trouble codes.
C. Wait at least 30 seconds in order for the diagnostic codes to become active.
Look for an active -13 code or for a logged -13 code.
Diagnostic Trouble Codes
Result: There is an active or there is a logged -13 code.
Proceed to Test Step 2.
2. Check for Debris
A. Turn the keyswitch to the OFF position.
B. Check the suspect sensor for debris.
C. If applicable, check the reference sensor for debris.
D. Check the sensor measurement port for blockage by debris.
E. If debris is found, clear the debris from the measurement port and replace the suspect sensor.
F. Turn the keyswitch to the ON position.
G. Check for -13 codes. Wait at least 30 seconds in order for the diagnostic codes to become active.
Debris
Result: The sensor measurement port is not blocked by debris.
Proceed to Test Step 3.
Result: A -13 code is not present, return the unit to service.
Result: A -13 code is present, replace the suspect sensor. Verify that the problem is resolved.
Result: If more than one -13 code is present and the codes have a reference sensor, replace the reference sensor. Verify that the problem is resolved.
3. Inspect the Suspect Sensor Connector
A. Turn the keyswitch to the OFF position.
Inspect the suspect sensor connector for moisture and/or corrosion.
Moisture
Result: The suspect sensor connector has moisture and/or corrosion.
Proceed to Test Step 4.
Result: The suspect sensor connector does not have moisture and/or corrosion.
Replace the affected sensor.
4. Remove any moisture and/or corrosion
A. Disconnect the suspect sensor connector.
B. Remove any moisture and/or corrosion from the outside of the connector. Check for moisture and corrosion inside the connector. Verify that the seals for the wires are sealing correctly. Refer to Troubleshooting, "Electrical Connectors - Inspect", if necessary.
C. If necessary, repair the connector or replace the connector.
D. Reconnect the connector. Verify that the connection is secure.
E. Turn the keyswitch to the ON position.
F. Monitor the diagnostic codes on Cat ET. Check for -13 codes. Wait at least 30 seconds in order for the diagnostic codes to become active.
Moisture
Result: A -13 code is not present, return the unit to service.
Result: A -13 code is present, replace the suspect sensor. Verify that the problem is resolved.
Result: If more than one -13 code is present and the codes have a reference sensor, replace the reference sensor. Verify that the problem is resolved.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts exhaust EVINRUDE:

0330073
 
0330073 EXHAUST COVER
CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E250CXARC, E250CXATF, E250CXEIE, E250CXEND, E250CXEOR, E275CLCUR, E275CXCCA, E300CLCUR, E300CXCCA, E300CXCEM, E300CXEIE, E300CXEND, E300CXEOR, E300CXERC, E300CXESB, E300CXETF
0332846
 
0332846 EXHAUST HOUSING
BE250CXECB, BE250CXEDA, BE250CXEUM, E250CXARC, E250CXATF, E250CXEIE, E250CXEND, E250CXEOR, E275CLCUR, E275CXCCA, E300CLCUR, E300CXCCA, E300CXCEM, E300CXEIE, E300CXEND, E300CXEOR, E300CXERC, E300CXESB, E300CXETF
0332848
 
0332848 EXHAUST HOUSING
E250CXARC, E250CXATF, E250CXEIE, E250CXEND, E250CXEOR, E275CLCUR, E275CXCCA, E300CLCUR, E300CXCCA, E300CXCEM, E300CXEIE, E300CXEND, E300CXEOR, E300CXERC, E300CXESB, E300CXETF
0333519
 
0333519 EXHAUST HOUSING, Inner
E250CXARC, E250CXATF, E250CXEIE, E250CXEND, E250CXEOR, E275CXCCA, E300CXCCA, E300CXCEM, E300CXEIE, E300CXEND, E300CXEOR, E300CXERC, E300CXESB, E300CXETF
0337551
 
0337551 EXHAUST HOUSING
E250CXARC, E250CXATF, E250CXEOR, E300CXEOR, E300CXERC, E300CXETF
Back to top