5008164 EVINRUDE EXHAUST HOUSING, 20 inch models


5008164 EXHAUST HOUSING, 20 inch models EVINRUDE E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHPLISS, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E25DELAAA, E25DELIIH, E25DELINA, E25DELISC, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLISC, E25DRAAA, E25DRIIH, EXHAUST
5008164 EXHAUST HOUSING, 20 inch models EVINRUDE
Rating:
23

Buy EXHAUST HOUSING, 20 inch models 5008164 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

E15DHPLAAA, E15HPSLAAA, E15HPSXAAA 2012
E15DHPLAAB, E15HPSLAAB, E15HPSXAAB 2012
E15DHPLIIC, E15DHPLIIH, E15HPSLIIH, E15HPSLIIS 2011
E15DHPLINR, E15HPSLINC, E15HPSXINC 2012
E15DHPLISS 2010
E15DHTLAAA, E15HTSLAAA, E15HTSXAAA 2012
E15DHTLAAB, E15HTSLAAB, E15HTSXAAB 2012
E15DHTLIIC, E15DHTLIIH, E15HTSLIIH, E15HTSLIIS 2011
E15DHTLINR, E15HTSLINC, E15HTSXINC 2012
E15DHTLISS 2010
E25DELAAA, E25DELAAB 2012
E25DELIIH, E25DELIIR 2011
E25DELINA 2012
E25DELISC 2010
E25DPLAAA, E25DPSLAAA 2012
E25DPLAAB, E25DPSLAAB 2012
E25DPLIIG 2011
E25DPLIIH, E25DPLIIR, E25DPSLIIH, E25DPSLIIS 2011
E25DPLINA, E25DPSLINC 2012
E25DPLISC 2010
E25DRAAA, E25DRAAB, E25DRLAAA, E25DRLAAB, E25DRSAAA, E25DRSAAB, E25DRSLAAA, E25DRSLAAB 2012
E25DRIIH, E25DRIIR, E25DRLIIH, E25DRLIIR, E25DRSIIH, E25DRSIIS, E25DRSLIIH, E25DRSLIIS 2011
E25DRINA, E25DRLINA, E25DRSINC, E25DRSLINC 2012
E25DRISC, E25DRLISC 2010
E25DTEAAA, E25DTEAAB, E25DTELAAA, E25DTELAAB, E25TESLAAA, E25TESLAAB 2012
E25DTEIIG 2011
E25DTEIIH, E25DTEIIR, E25DTELIIH, E25DTELIIR, E25TESLIIH, E25TESLIIS 2011
E25DTEINA, E25DTELINA, E25TESLINC 2012
E25DTEISC, E25DTELISC 2010
E25DTLAAA, E25DTSLAAA 2012
E25DTLAAB, E25DTSLAAB 2012
E25DTLIIH, E25DTLIIR, E25DTSLIIH, E25DTSLIIS 2011
E25DTLINA, E25DTSLINC 2012
E25DTLISC 2010
E30DELAAA, E30DELAAB 2012
E30DELIIH, E30DELIIR 2011
E30DELINA 2012
E30DELISC 2010
E30DPLAAA, E30DPSLAAA 2012
E30DPLAAB, E30DPSLAAB 2012
E30DPLIIH, E30DPLIIR, E30DPSLIIH, E30DPSLIIS 2011
E30DPLINA, E30DPSLINC 2012
E30DPLISC 2010
E30DRAAA, E30DRAAB, E30DRLAAA, E30DRLAAB, E30DRSAAA, E30DRSAAB, E30DRSLAAA, E30DRSLAAB 2012
E30DRIIG, E30DRLIIG 2011
E30DRIIH, E30DRIIR, E30DRLIIH, E30DRLIIR, E30DRSIIH, E30DRSIIS, E30DRSLIIH, E30DRSLIIS 2011
E30DRINA, E30DRLINA, E30DRSINC, E30DRSLINC 2012
E30DRISC, E30DRLISC 2010
E30DTELAAA, E30DTELAAB, E30TESLAAA, E30TESLAAB 2012
E30DTELIIH, E30DTELIIR, E30TESLIIH, E30TESLIIS 2011
E30DTELINA, E30TESLINC 2012
E30DTELISC 2010
E30DTLAAA, E30DTSLAAA 2012
E30DTLAAB, E30DTSLAAB 2012
E30DTLIIH, E30DTLIIR, E30DTSLIIH, E30DTSLIIS 2011
E30DTLINA, E30DTSLINC 2012
E30DTLISC 2010

Information:

Storage Procedure
1. Clean the outside of the engine and repaint areas that have paint damage with a good quality paint.2. Remove the batteries and use them in some other place or put them in storage where they can be checked and electrically charged again when needed. If the batteries are not removed, wash the tops. Put an electrical charge to the battery to a specific gravity of 1.275. Disconnect the battery terminals. Put a plastic cover over the battery.3. Loosen all fan, alternator belts, etc. Attach a tag to indicate what work has been done.4. Put a waterproof cover over engines with enclosures stored outdoors. Make the cover tight, but loose enough to allow air to circulate around the engine to prevent damage to exposed metal parts from condensation. Remove the waterproof cover every two or three months and check the engine for corrosion. If the engine has signs of corrosion at the check period, follow the protection procedure again. To operate the engine, it is not necessary to remove the preservative oil mixture. If a compartment under protection of VCI vapors is opened, put more VCI mixture in to make up for the vapor loss. Install all covers and/or put tape over all openings, air intake, exhaust openings, flywheel housing, crankcase breathers, dipstick tubes, etc. Make sure all covers are air tight and weatherproof. Use a waterproof, weather resistant tape.5. Put lubricant on all points given in the Lubrication and Maintenance Chart.6. Put a heavy amount of multipurpose grease on all outside parts that move; rod threads, ball joints, linkage, etc.7. Oil and oil filter elements used less than 50 hours in the engine do not need to be changed. (Otherwise, change the oil, filling the engine to the "add oil" mark on the dipstick.) Add 3% to 4% of VCI oil per engine volume. If the engine is drained, install a mixture of 50% VCI oil and 50% engine oil in the crankcase and in all lubricating oil compartments at the rate of one part VCI oil mixture per fifteen parts of compartment capacity at full level. If possible, operate the engine three to five minutes. Put tape over all openings to seal VCI vapors in the engine. If necessary, drain some lubricant to add to the mixture.8. Remove any dirt from the air cleaner. Check all seals and gaskets.9. Remove the air filter elements. Turn the engine at cranking speed with throttle control in fuel OFF position, remove pressure plug for boost pressure and use a sprayer to add a mixture of 50% VCI oil and 50% engine oil. Minimum application rate is 5.5 milliliters per liter (3 oz. per 1000 cubic inches) of engine displacement.10. Fill the oil reservoir for the air starter with a mixture of 50% VCI oil and 50% engine oil.11. Use a sprayer to put a mixture of 50% VCI oil and 50% engine oil into the exhaust openings. Minimum application rate is 5.5 milliliters per liter (3 oz. per 1000 cubic inches) of engine displacement.12. Also, use a sprayer to apply a mixture of 50% VCI oil and 50% engine oil on the flywheel, ring gear teeth and starter pinion. Install the covers to keep the vapors in.13. Remove the fuel nozzles and install 30 milliliters (1 oz) of 50% VCI oil and 50% engine oil in each cylinder. Test (using calibrating oil) then install fuel nozzles and tighten all fittings to the correct torque. Use an engine turning tool to turn the engine over slowly two complete revolutions in the direction of normal rotation, to put oil on the cylinder walls.14. Remove the fuel from the secondary fuel filter housing or change the spin-on fuel filter element to get out any dirt and water. Clean the primary fuel filter, fill with calibration oil and operate the priming pump. This will get clean oil to the secondary fuel filter and engine, and help to prevent "sticky" fuel pump nozzles during extended storage.Calibration oil is available from your Caterpillar dealer in two sizes, 208 liters (55 gallons) or 19 liters (5 gallons). Open the fuel tank drain valve and remove any water or dirt from the inside of the fuel tank.The fuel must be treated with a Biocide, which prevents bacteria and fungi from contaminating diesel fuel that contains some water. Microbial contamination can cause severe fuel system blockage, filter plugging, fuel pump sticking and corrosion.Additional information as to ordering and use of diesel fuel Biocide and a list of suppliers outside the U.S.A. are available from:Amalgamated Coal & Petroleum
Specialists, Inc.
C.P.S. Associates
9214 Ernst Road
Fort Wayne, Indiana 46809
Telephone (219) 747-7080
Methyl Cellosolve will help assimilate water in the fuel and prevent freezing problems. Fill the fuel tank with the treated fuel.Seal all openings to the tank to prevent evaporation of the fuel.15. Withdraw a sample of coolant and check it for clarity (rust) and freezing point. If it contains suspended particles or does not provide freeze protection to at least -23°C (-10°F), the coolant should be drained. Completely drain the cooling system, if needed. The cooling system must be thoroughly flushed and chemically cleaned.16. Refill the cooling system with a coolant solution that is 50% water and 50% ethylene glycol. Install a new precharge coolant conditioner element (if equipped with coolant conditioner elements). A 3% to 6% concentration of coolant conditioner does not have to be added, if the cooling system is filled with coolant solution to the top of the filler neck. Attach a tag indicating what has been done. Do not use coolant conditioner elements or liquid coolant conditioner with Dowtherm 209 Full-Fill coolant.Procedure for Operation After Storage
1. Remove all outside protective covers, and any tape or grease used for protection.2. Drain the VCI oil and engine oil mixture from the engine, if the oil has been in the engine for more than one year, or if the engine was left drained before adding the VCI mixture. If storage was short term, the engine can be operated with a 3%


Parts exhaust EVINRUDE:

5008165
 
5008165 EXHAUST HOUSING, 15 inch models
E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHPLISS, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E25DELAAA, E25DELIIH, E25DELINA, E25DELISC, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLISC, E25DRAAA, E25DRIIH,
5008254
 
5008254 EXHAUST HOUSING, 25 inch models Exhaust emissions related part
E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E25DELAAA, E25DELIIH, E25DELINA, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DRAAA, E25DRIIH, E25DRINA, E25DTEAAA, E25DTEIIG, E25DTEIIH, E25
Back to top