0393784 EVINRUDE FLOAT CHAMBER ASSY., Lower


0393784 FLOAT CHAMBER ASSY., Lower EVINRUDE E100WMLCDR, E110MLCDC, E115MLCOS, E115MLCRD, E140TLCRD, E150ANCRS, E150STLCOH, E150TLCDC, E150TLCOS, E150TLCRD, E155WTLCDR, E155WTLCOC, E155WTLCRS, E175TLCDR, E175TLCOC, E185TLCOC, E185TLCRS, E235STLCOR, E235STLCRC, E235TLCOR, E235TLCRC, E90MLCDC, E9 FLOAT
0393784 FLOAT CHAMBER ASSY., Lower EVINRUDE
Rating:
25

Buy FLOAT CHAMBER ASSY., Lower 0393784 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

BRP EVINRUDE entire parts catalog list:

E100WMLCDR, E100WTLCDR, E100WTXCDR 1986
E110MLCDC, E110TLCDC, E110TLCDF 1986
E115MLCOS, E115TLCOS 1985
E115MLCRD, E115TLCRD, E115TXCRD 1984
E140TLCRD, E140TXCRD 1984
E150ANCRS, E150STLCRD 1984
E150STLCOH, E150STLCOS 1985
E150TLCDC, E150TXCDC 1986
E150TLCOS, E150TXCOS 1985
E150TLCRD, E150TXCRD 1984
E155WTLCDR, E155WTXCDR 1986
E155WTLCOC, E155WTXCOC 1985
E155WTLCRS, E155WTXCRS 1984
E175TLCDR, E175TXCDR 1986
E175TLCOC, E175TXCOC 1985
E185TLCOC, E185TXCOC 1985
E185TLCRS, E185TXCRS 1984
E235STLCOR 1985
E235STLCRC 1984
E235TLCOR, E235TXCOR 1985
E235TLCRC, E235TXCRC 1984
E90MLCDC, E90TLCDC, E90TXCDC 1986
E90MLCOS, E90TLCOS, E90TXCOS 1985
E90MLCRD, E90TLCRD, E90TXCRD 1984

Information:


Table 1
Diagnostic Codes Table
CDL Code J1939 Code Code Description Comments
110-3 110-3 Engine Coolant Temperature Sensor : Voltage Above Normal The code is logged if the engine has been running for more than seven minutes and an open circuit has been detected.
110-4 110-4 Engine Coolant Temperature Sensor : Voltage Below Normal The code is logged. The ECM detects voltage that is not in the acceptable range.
174-3 174-3 Fuel Temperature Sensor : Voltage Above Normal The code is logged. The ECM will flag the fuel temperature as invalid data and the fuel temperature is set to a default value of 40 °C (104 °F).
174-4 174-4 Fuel Temperature Sensor : Voltage Below Normal
1836-3 1385-3 Auxiliary Temperature Sensor : Voltage Above Normal The code is logged. The ECM will flag the temperature as invalid data and the temperature is set to a default value.
1836-4 1385-4 Auxiliary Temperature Sensor : Voltage Below Normal The code is logged. The ECM will flag the temperature as invalid data and the temperature is set to a default value.
2526-3 172-3 Air Inlet Temperature Sensor : Voltage Above Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
2526-4 172-4 Air Inlet Temperature Sensor : Voltage Below Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
3372-3 2630-3 Engine Charge Air Cooler #1 Outlet Temperature Sensor : Voltage Above Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
3372-4 2630-4 Engine Charge Air Cooler #1 Outlet Temperature Sensor : Voltage Below Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
3386-3 412-3 EGR Temperature Sensor : Voltage Above Normal The code is logged.
This code will not become active during Cold Mode. Run the engine to exit cold mode before troubleshooting a 3386-3 code.
The ECM detects voltage that is not in the acceptable range.
3386-4 412-4 EGR Temperature Sensor : Voltage Below Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
3683-3 442-3 Auxiliary Temperature #2 : Voltage Above Normal The code is logged.
The ECM detects voltage that is not in the acceptable range.
3683-4 442-4 Auxiliary Temperature #2 : Voltage Below Normal The code is logged.
The ECM detects voltage that is not in the acceptable range. System OverviewThe sensor signal for the passive sensor is routed from the ECM to terminal 1 of each sensor connector. The sensor return for the passive sensors is routed to the ECM from terminal 2 of each sensor connector.Diagnostics on the Caterpillar Electronic Technician (ET)Wiggle Test - The Wiggle Test allows you to monitor the status of the signals from the sensors.For additional information regarding the Wiggle Test, refer to the documentation that accompanies the Cat ET software.
Illustration 1 g03330022
Schematic for the passive analog sensors
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Connect to Cat® Electronic Technician (ET).
B. Turn the keyswitch to the ON position.
C. Access the "Active Diagnostic Code" screen on Cat ET.
Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Look for these active codes or logged codes:
-3
-4
Codes
Result: A -3 diagnostic code is active.
Proceed to Test Step 2.
Result: A -4 diagnostic code is active.
Proceed to Test Step 3.
Result: To troubleshoot a logged 3386-3 or a 412-3 diagnostic code during cold mode, Proceed to Test Step 5.
This code will not become active during cold mode.
Result: For a diagnostic code that is logged but not currently active, Proceed to Test Step 4.
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the suspect sensor.
C. Install the jumper wire between terminal 1 (sensor signal) and terminal 2 (sensor return) at the sensor connector.
D. Turn the keyswitch to the ON position.
E. Monitor the diagnostic codes on Cat ET. Check for an active -4 diagnostic code for the suspect sensor.
Wait at least 30 seconds in order for the diagnostic codes to become active.
F. Turn the keyswitch to the OFF position.
Short Circuit
Result: The -3 diagnostic code remains active for the suspect sensor.
Repair: There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Result: A -4 diagnostic code became active after creating the short at the sensor connector.
Repair: The wiring is OK. Replace the sensor.
Verify that the problem is resolved.
3. Create an Open at the Suspect Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor connector of the suspect sensor with the active -4 diagnostic code.
C. Turn the keyswitch to the ON position.
D. Monitor the diagnostic codes on Cat ET. Check for an active -3 diagnostic code for the suspect sensor.
Wait at least 30 seconds in order for the diagnostic codes to become active.
A 412-3 or a 3386-3 code will not become active during "Cold Mode". Run the engine to exit cold mode before troubleshooting a 412-3 or a 3386-3 code.
For a 110-3 code, start the engine and let the engine idle for 7 minutes. The engine must be running for at least 7 minutes in order for the diagnostic to run.
E. Turn the keyswitch to the OFF position.
Open Circuit
Result: The -4 diagnostic code remains active for the suspect sensor.
Repair: There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Result: A -3 diagnostic code became active after disconnecting the sensor.
Repair: The wiring is OK. Replace the sensor.
Verify that the problem is resolved.
4. Perform the Wiggle Test
Carefully following this procedure is the best way to identify the root cause of an intermittent problem.
A. Turn the keyswitch to the ON position.
B. Use Cat ET to run the "Wiggle Test".
C. Slowly wiggle the wiring and the connectors between the P2 connector and the sensor. Slowly wiggle the wiring and the connectors between the P1 connector and the sensor. Pay particular attention to the wiring near each connector. Be sure to wiggle all of the wiring.
D. As you wiggle the wiring look for these problems.
·


Parts float EVINRUDE:

0302559
FLOAT,Indicator
0302559 FLOAT,Indicator
100193A, 100293R, 100882B, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 18002C,
0383437
FLOAT ASSEMBLY
0383437 FLOAT ASSEMBLY
100193A, 100293R, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85693
0387658
 
0387658 FLOAT VALVE ASSY.
150840S, 150940C, 175740S, 200640S, E100MLCSC, E100WMLCRS, E115MLCIH, E115MLCNB, E115MLCSA, E115MLCTE, E140MLCIH, E140MLCNB, E140MLCSA, E140MLCTE, E150STLCTE, E150TRLCIA, E150TRLCNM, E150TRLCSF, E150TRLCTB, E155WTLCOC, E155WTLCRS, E175TRLCIM, E175TRL
0393785
 
0393785 FLOAT CHAMBER ASSY., Upper
E110MLCDC, E115MLCOS, E115MLCRD, E140TLCRD, E90MLCDC, E90MLCOS, E90MLCRD
0394970
 
0394970 FLOAT VALVE ASSY.
E100WMLCOC, E115MLCOS, E115MLCRD, E140TLCRD, E150ANCRS, E150STLCOH, E150TLCOS, E150TLCRD, E175TLCOC, E185TLCOC, E185TLCRS, E235STLCOR, E235STLCRC, E235TLCOR, E235TLCRC, E90MLCOS, E90MLCRD, U25RWA
0396520
 
0396520 FLOAT VALVE ASSY.
BE115TLEDA, C155WTLM, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCDR, E100WTLCUA, E100WTLEDR, E100WTLEIB, E100WTLENE, E100WTLEOC, E100WTLERS, E100WTLESM, E100WTLETD, E100WTLEUA, E100WTLZ, E110MLCCA, E11
Back to top