0331576 EVINRUDE APPLIQUE, Rear

Table 1
Diagnostic Codes Table
J1939 Code and Description Conditions which Generate this Code System Response
1180-3
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Above Normal The ECM detects a duty cycle that is greater than 96 percent for ten seconds. The code is logged.
If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value is used.
1180-4
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Below Normal The ECM detects a duty cycle that is less than 4 percent for ten seconds.
1180-8
Engine Turbocharger 2 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period The ECM detects a sensor frequency that is greater than 600 Hz or less than 400 Hz.
1181-3
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Above Normal The ECM detects a duty cycle that is greater than 96 percent for ten seconds. The code is logged.
If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value is used.
1181-4
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Below Normal The ECM detects a duty cycle that is less than 4 percent for ten seconds.
1181-8
Engine Turbocharger 1 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period The ECM detects a sensor frequency that is greater than 600 Hz or less than 400 Hz.
2452-8
Generator Total Real Power : Abnormal Frequency, Pulse Width, or Period The ECM detects a sensor frequency that is greater than 600 Hz or less than 400 Hz. The code is logged.
Gas substitution shuts off. System OperationUse this procedure to troubleshoot any suspect problems with the sensor for the left turbocharger turbine inlet temperature or the right turbocharger turbine inlet temperature.The Pulse Width Modulated Sensor (PWM) provides a signal to the ECM. The PWM signal is used to represent certain engine operating conditions. The sensors receive 8.0 0.4 VDC from a regulated power supply.The ECM performs an automatic calibration of these sensors whenever the ECM is powered and the engine has been off for at least 5 seconds.The ECM provides short circuit protection for the internal power supply. A short circuit to the battery will not damage the internal power supply.The following components can cause problems with the power supply:
Electrical connector or wiring
Sensor
ECMThe most likely cause of a problem is a problem with an electrical connector or wiring. The least likely cause is a problem with the ECM.
Illustration 1 g03382002
Schematic of the PWM sensors for the sensor signal circuit
Illustration 2 g03382006
Terminal locations at the P1 ECM connector for the sensors for the turbocharger turbine inlet temperature.
(P1-4) Digital sensor supply
(P1-5) Digital return
Illustration 3 g03382009
Terminal locations at the P2 ECM connector for the sensors for the turbocharger turbine inlet temperature.
(P2-65) Left turbocharger turbine inlet temperature
(P2-73) Right turbocharger turbine inlet temperature
Illustration 4 g01159881
Terminal locations at the connectors for the exhaust temperature sensor
(Terminal A) Digital sensor supply
(Terminal B) Digital return
(Terminal C) Signal
Table 2
Troubleshooting Test Steps Values Results
1. Check for an "Active" Diagnostic Codes
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector.
B. Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
C. Determine if a diagnostic code has occurred several times.
Note: A diagnostic code that is logged several times is an indication of an intermittent problem. Most intermittent problems are the result of a bad connection between a socket and a pin in a connector. There could also be a bad connection between a wire and a terminal.
D. Look for one or more of the following diagnostic codes that are active or logged:
- 1181-3
- 1181-4
- 1181-8
- 1180-3
- 1180-4
- 1180-8
Codes
Result: No diagnostic codes are active.
Repair: There may be an intermittent problem in the harness or in a connector. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct procedures for inspecting electrical connectors.
Result: One of the diagnostic codes that are listed above are active or logged.
The ECM detects a problem in one of the circuits for the exhaust temperature sensors.
Proceed to Test Step 2.
2. Check the Digital Supply Voltage at the Sensor Connector
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the suspect sensor at the sensor connector:
C. Restore the electrical power to the ECM.
D. Measure the supply voltage on the harness side of the sensor connector. Measure the voltage between terminal A and terminal B for the suspect sensor.
8.0 0.4 VDC
Result: The supply voltage is 8.0 0.4 VDC. The supply voltage is reaching the sensor connector.
Proceed to Test Step 4.
Result: The supply voltage is not 8.0 0.4 VDC. The supply voltage is not reaching the sensor connector.
Proceed to Test Step 3.
3. Check the Digital Supply Voltage at the ECM
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the J1/P1 ECM connector.
C. Fabricate a jumper wire that is long enough to use as a test lead at the ECM connector. Crimp a connector socket to one end of the jumper wire.
D. Remove the wire for the digital supply from terminal location P1-4. Install the jumper wire into the terminal location.
E. Connect the J1/P1 ECM connector.
F. Restore the electrical power to the ECM.
G. Measure the voltage between the jumper wire that is in terminal P1-4 and P1-5.
H. Turn the main disconnect switch to the OFF position.
I. Restore the wiring to the original configuration.
8.0 0.4 VDC.
Result: The supply voltage at the ECM is 8.0 0.4 VDC.
Repair: The supply voltage at the ECM is correct. There is a problem in the wiring between the ECM and the sensor co