0174062 EVINRUDE FUEL CONN, Hose & bulb assy.


0174062 FUEL CONN, Hose & bulb assy. EVINRUDE E10ECDB, E10ECOM, E10ELCRA, E120TLCOS, E140TLCOS, E15ECDE, E15ECOB, E15ECRM, E200STLCDR, E225PTLCDA, E25RWCDC, E25RWCOS, E25RWCRD, E28ELCDS, E28ELCDS, E40RWCDB, E40RWCOM, E40RWCRA, E45RCCDS, E4RDHCDE, E55RWLCDC, E55RWLCOS, E55RWLCRD, E65RWLCDR, E65RW FUEL
0174062 FUEL CONN, Hose & bulb assy. EVINRUDE
Rating:
8

Buy FUEL CONN, Hose & bulb assy. 0174062 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 17406
 

BRP EVINRUDE entire parts catalog list:

E10ECDB, E10ELCDB, E10RCDB, E10RLCDB, E10SELCDB 1986
E10ECOM, E10ELCOM, E10RCOM, E10RLCOM, E10SELCOM 1985
E10ELCRA, E10RCRA, E10RLCRA, E10SELCRA 1984
E120TLCOS, E120TXCOS 1985
E140TLCOS, E140TXCOS 1985
E15ECDE, E15ELCDE, E15RCDE, E15RLCDE 1986
E15ECOB, E15ELCOB, E15RCOB, E15RLCOB 1985
E15ECRM, E15ELCRM, E15RCRM, E15RLCRM 1984
E200STLCDR, E200TXCDS 1986
E225PTLCDA, E225PTXCDA, E225TLCDA, E225TXCDA 1986
E25RWCDC, E25RWLCDC 1986
E25RWCOS, E25RWLCOS 1985
E25RWCRD, E25RWLCRD 1984
E28ELCDS 1986
E28ELCDS 1986
E40RWCDB, E40RWLCDB 1986
E40RWCOM, E40RWLCOM 1985
E40RWCRA, E40RWLCRA 1984
E45RCCDS, E45RCLCDS 1986
E4RDHCDE 1986
E55RWLCDC 1986
E55RWLCOS 1985
E55RWLCRD 1984
E65RWLCDR, E65TELCDR 1986
E65RWLCOC, E65TELCOC 1985
E65RWLCRS, E65TELCRS, E65WTLCRS 1984
E65WMLCDR 1986
E65WMLCOC, E65WTLCOC 1985
E6RCDE, E6RLCDE, E6SLCDE 1986
E6RCOB, E6RLCOB, E6SLCOB 1985
E6RCRM, E6RLCRM, E6SLCRM 1984
E8RCDE, E8RLCDE, E8SRLCDE 1986
E8RCOB, E8RLCOB, E8SRLCOB 1985
E8RCRM, E8RLCRM, E8SRLCRM 1984

Information:


Table 1
Diagnostic Trouble Codes For The Glow Plug Starting Aid
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
676-5 2246-5 Engine Glow Plug Relay : Current Below Normal The Electronic Control Module (ECM) detects the following conditions:
The engine is not cranking.
The ECM has been powered for at least one second.
There is a low current condition (open circuit) in the glow plug start aid relay circuit for more than 2 seconds.
The warning light will come on. The diagnostic code will be logged. An ECM that was previously blank will require a total of 2 hours of operation before the diagnostic code will be logged.
The ECM is unable to activate the relay for the glow plug starting aid. The glow plugs will not operate. The engine may be difficult to start in cold temperatures and the exhaust may emit white smoke.
676-6 2246-6 Engine Glow Plug Relay : Current Above Normal The Electronic Control Module (ECM) detects the following conditions:
The engine is not cranking.
The ECM has been powered for at least one second.
There is a high current condition (short circuit) in the glow plug start aid relay circuit for more than 2 seconds.
The warning light will come on. The diagnostic code will be logged. An ECM that was previously blank will require a total of 2 hours of operation before the diagnostic code will be logged.
The ECM is unable to activate the relay for the glow plug starting aid. The glow plugs will not operate or the glow plugs will operate all the time. The engine may be difficult to start in cold temperatures and the exhaust may emit white smoke.
Follow the troubleshooting procedure to identify the root cause of the fault. The following background information is related to this procedure:The starting aid is used to improve the engine starting when the engine is cold. With the keyswitch in the ON position, the ECM monitors the following parameters to decide if the glow plugs need to be switched ON:
Coolant temperature
Intake manifold air temperatureIf the glow plugs are required, then the ECM will activate the starting aid relay for a controlled period. While the glow plug start aid relay is activated, the glow plug start aid relay will supply power to the glow plugs. If a "Wait To Start" lamp is installed, then this lamp will be illuminated to indicate the "Wait To Start" period."Wait to Start Lamp"This feature may be included as an option.When glow plugs need to be activated prior to starting, a lamp will indicate that the operator needs to "Wait to Start". Starting aids may be used during the cranking of the engine. Starting aids may be used if the engine has previously been started. The "Wait to Start" lamp will not be active in these conditions.Electronic Service Tool Test AidThe electronic service tool includes the test "Glow Plug Start Aid Override Test". This test will assist the analysis of the cold starting aid.Overview of the Glow Plug Start Aid Override TestThis glow plug start aid override test switches on the cold starting aid when the engine is not running. The glow plug start aid override test aids the analysis of the circuit for the glow plug start aid relay.
Illustration 1 g03815124
Schematic for the glow plug starting aid circuit
Not all connectors are shown. Refer to the appropriate Electrical Schematic.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Check that the fuses are not blown.
B. Inspect the terminals on the glow plug start aid relay and then inspect the connector on the flying lead from the relay. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Inspect the bus bar for the glow plugs. Ensure that the nuts that secure the bus bar to each glow plug are tightened to a torque of 2 N m (17 lb in). Ensure that the bus bar is not shorted to the engine.
D. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the glow plug starting aid.
E. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
F. Check the harness for abrasion and pinch points from the glow plugs back to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points. The fuses are not blown. The bus bar is secured to the glow plugs and not shorted to ground.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position.
Note: Do not start the engine.
C. Use the electronic service tool to select the "Glow Plug Start Aid Override Test" to turn on the power for the glow plugs.
D. Check for active diagnostic codes or recently logged diagnostic codes that are listed in Table 1.
Diagnostic codes
Result: No diagnostic codes are present.
There may be an intermittent fault in an electrical component between the ECM and the glow plugs. The problem may be inside an electrical connector. Refer to Troubleshooting, "Electrical Connector - Inspect" to identify intermittent faults.
There may be a fault in the glow plug switched power circuit. The ECM does not monitor the status of this condition.
Proceed to Test Step 7 to test this circuit.
Result: Diagnostic code 676-5 or 2246-5 is active or recently logged.
Proceed to Test Step 3.
Result: Diagnostic code 676-6 or 2246-6 is active or recently logged.
Proceed to Test Step 5.
3. Create a Short Circuit at the Relay Connector
A. Turn the keyswitch to the OFF position.
B. Remove the glow plug start aid relay.
C. Fabricate a jumper wire. Install the jumper wire between Test Point 1


Parts fuel EVINRUDE:

0392062
FUEL LINE, Screen, nipple assy.
0392062 FUEL LINE, Screen, nipple assy.
E4BRHCOB, E5RCIC, E5RHCNR, E5RHCTA, E6RCRM, E8RCIC, E8RCNR, E8RCRM, E8RCTA
0392909
 
0392909 FUEL TANK ASSY. WITH GAUGE
E10ECOM, E10ELCNS, E10ELCRA, E10ELCTC, E115MLCNB, E115MLCOS, E115MLCRD, E115MLCTE, E140MLCNB, E140MLCTE, E140TLCRD, E15ECNC, E15ECOB, E15ECRM, E15ECTR, E20CRCOS, E25CNE, E25ECOC, E25ECRS, E25ECTD, E25RSLS, E25RWCOS, E25RWCRD, E30ECOA, E30ECRR, E35ECN
0393334
 
0393334 FUEL CONNECTOR
BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE50DTLEDC, BE60ELEDR, BE70ELEDA, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCRS,
0173639
 
0173639 FUEL CONNECTOR,Hose & bulb assy.
E10ELCRA, E10ELCTC, E15ECRM, E15ECTR, E30ECDM, E30ECOA, E30ECRR, E35ECRR, E35ECTS, E35RCDM, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA, E45RCCDS, E55RSLN, E55RWLCDC, E55RWLCOS, E55RWLCRD
0394789
 
0394789 FUEL PUMP ASSY.
E6RCRM, E8RCRM
0395717
0396305
 
0396305 FUEL CONNECTOR & HOSE
E120TLCDC, E120TLCOS, E140TLCDC, E140TLCOS, E200STLCDR, E225PTLCDA, E60ELCDS, E75ECDC
0397444
FUEL CONNECTOR ASSY.
0397444 FUEL CONNECTOR ASSY.
BE20SEEDA, BE20SREDA, BE25BAEDR, BE25EEDM, BE30BAEDE, BE30EEDE, BE40EEDS, BE40EEUC, BE4RDHEDS, BE50BEEDS, BE50RLEUC, E10ECCD, E10ECES, E10ECUE, E10EEIR, E10EENA, E10EESC, E15ECCS, E15ECEC, E15ECUD, E15EEIA, E15EENM, E15EESR, E20CRCCA, E20CRCEM, E20CR
Back to top