5041040 Fuel Hose & Primer Bulb Assembly Evaporative emissions related part EVINRUDE
B10EL4INS, B10PL4INS, B10PX4INS, B10R4INS, B10RL4INS, B10TEL4INS, B10TPL4INS, B10TPX4INS, B15PL4INS, B15R4INS, B15RL4INS, B15TE4INS, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10EL4INS, E10PL4INS, E15PL4INS, E15R4INS
Fuel
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$58.53
27-11-2023
6.3 Kilograms
-: -
Seachoice Folding Grapnel Boat Anchor, 13 Lbs., Steel
Dependable anchor can be folded up to reduce its size for easy storage when not in use || Versatile anchor can be locked in either the open or closed position || Rugged anchor is made of malleable iron || Heavily galvanized for long-term corrosion-resistant performance || Ideal for use by small watercraft and dinghies || Reliable anchor weighs 13 pounds || Manufacturer part number 50-41040
Dependable anchor can be folded up to reduce its size for easy storage when not in use || Versatile anchor can be locked in either the open or closed position || Rugged anchor is made of malleable iron || Heavily galvanized for long-term corrosion-resistant performance || Ideal for use by small watercraft and dinghies || Reliable anchor weighs 13 pounds || Manufacturer part number 50-41040
Compatible models:
BRP EVINRUDE entire parts catalog list:
- FUEL TANK ASSEMBLY » 5041040
B10PX4INS, E10PX4INS 2012
B10R4INS, E10R4INS 2012
B10RL4INS, E10RL4INS 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012
B15PL4INS 2012
B15R4INS, E15RL4INS 2012
B15RL4INS, B15TEL4INS, E15TE4INS, E15TEL4INS 2012
B15TE4INS 2012
B4R4AAA, B4R4AAB, B4RL4AAA, B4RL4AAB, E4R4AAA, E4R4AAB, E4RL4AAA, E4RL4AAB 2012
B4R4INS, B4RL4INS, E4R4INS, E4RL4INS 2012
B6R4AAA, B6R4AAB, B6RL4AAA, B6RL4AAB, B6RX4AAA, B6RX4AAB, E6R4AAA, E6R4AAB, E6RL4AAA, E6RL4AAB, E6RX4AAA, E6RX4AAB 2012
B6R4INS, B6RL4INS, B6RX4INS, E6R4INS, E6RL4INS, E6RX4INS 2012
E10EL4INS 2012
E10PL4INS 2012
E15PL4INS 2012
E15R4INS 2012
Information:
1. Disconnect connector (1). 2. Attach Tool (A) and fasten a hoist.3. Remove four bolts (3) and stack (2). The weight of the stack and hardware is 45 kg (99 lb). 4. Remove hose clamp (6).5. Remove five bolts (5) and support (4).6. Repeat Steps 4 and 5 for the other side of the engine. 7. Remove six bolts (7) that connect oil pan (8) to flywheel housing (9). Loosen the rest of the bolts that hold the oil pan in position. 8. Attach Tool (A) to the flywheel housing and a hoist. 9. Lift the end of the engine enough so a 1/2 ( in) Hardened Washer (10) can be installed on each side of the engine between the oil pan and the cylinder block.10. Install blocks under the oil pan to support the engine when the flywheel housing is removed. Lower the engine onto the blocks. 11. Remove twenty one bolts (11) and flywheel housing (9). The weight of the flywheel housing is approximately 91 kg (201 lb).Install Flywheel Housing
1. Install two 1/2 in-13 NC × 101 mm (4 in) Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (201 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts: a. Tighten bolts 1 through 20 in number sequence to a torque of 40 10 N m (30 7 lb ft).b. Tighten the 3/8" bolts in number sequence to a torque of 55 10 N m (41 7 lb ft). Tighten the 1/2" bolts in number sequence to a torque of 135 20 N m (100 15 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8. Repeat Step (7) for the other side of the engine. 9. Use Tool (A) to lift stack (2) in place. Install the stack to the engine with four bolts (3). 10. Connect connector (1).End By:a. install crankshaft rear seal and wear sleeveb. install all turbochargers
1. Install two 1/2 in-13 NC × 101 mm (4 in) Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (201 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts: a. Tighten bolts 1 through 20 in number sequence to a torque of 40 10 N m (30 7 lb ft).b. Tighten the 3/8" bolts in number sequence to a torque of 55 10 N m (41 7 lb ft). Tighten the 1/2" bolts in number sequence to a torque of 135 20 N m (100 15 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8. Repeat Step (7) for the other side of the engine. 9. Use Tool (A) to lift stack (2) in place. Install the stack to the engine with four bolts (3). 10. Connect connector (1).End By:a. install crankshaft rear seal and wear sleeveb. install all turbochargers
Parts fuel EVINRUDE:
5040847
5040067
5040067 *Fuel Filter Assembly Exhaust & Evaporative emissions related part
B4R4AAA, B4R4INS, B6R4AAA, B6R4INS
5040977
5040977 Fuel Pump Assembly
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10EL4AAB, E10EL4INS, E1
5040140
5040140 Fuel Filter Assembly Exhaust & Evaporative emissions related part
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5041097
5040891
5040892
5041111