5004456 EVINRUDE *FUSABLE LINK KIT, AUX. BATTERY


5004456 *FUSABLE LINK KIT, AUX. BATTERY EVINRUDE E100FPLSOC, E100FPLSRS, E115FPLSDS, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSSH, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLSDS, E135FCXSDE, E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSSS, E135FCXSTA, E135FPLSDE, E135FPLSOB, E135FPLSRM FUSABLE
5004456 *FUSABLE LINK KIT, AUX. BATTERY EVINRUDE
Rating:
73

Buy *FUSABLE LINK KIT, AUX. BATTERY 5004456 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 103
 

BRP EVINRUDE entire parts catalog list:

E100FPLSOC, E100FSLSOC 2004,2005
E100FPLSRS, E100FSLSRS 2004
E115FPLSDS 2006
E115FPLSNF, E115FPXSNF 2002
E115FPLSOD, E115FSLSOD 2004,2005
E115FPLSRE, E115FSLSRE 2004
E115FPLSSH, E115FPLSSR, E115FPXSSH, E115FPXSSR, E115FSLSSH, E115FSLSSR, RE115FLSSSH, RE115FLSSSR, RE115FPLSSH, RE115FPLSSR, RE115FSSSH, RE115FSSSR, RE115FXSSH, RE115FXSSR 2000
E115FPLSTB, E115FPXSTB, E115FSLSTB 2003
E115FPXSDS 2006
E115FPXSOD 2004,2005
E115FPXSRE 2004
E115FSLSDS 2006
E135FCXSDE 2006
E135FCXSNF, E135FPLSNF, E135FPXSNF 2002
E135FCXSOB 2004,2005
E135FCXSRM 2004
E135FCXSSS, E135FPLSSS, E135FSLSSS, E135FSXSSS, RE135FCSSS, RE135FLSSS, RE135FXSSS 2000
E135FCXSTA 2003
E135FPLSDE 2006
E135FPLSOB, E135FSLSOB 2004,2005
E135FPLSRM, E135FSLSRM 2004
E135FPLSTA, E135FPXSTA 2003
E135FPXSDE 2006
E135FPXSOB 2004,2005
E135FPXSRM 2004
E135FSLSDE 2006
E135FSLSTA 2003
E150FCXSDR 2006
E150FCXSNF, E150FPLSNF, E150FPXSNF 2002
E150FCXSOC 2004,2005
E150FCXSRS 2004
E150FCXSSM, E150FCXSSV, E150FPLSSM, E150FPLSSV, E150FPXSSM, E150FPXSSV, E150FSLSSM, E150FSLSSV, RE150FCSSM, RE150FCSSV, RE150FLSSM, RE150FLSSV, RE150FSSM, RE150FSSV, RE150FXSSM, RE150FXSSV 2000
E150FCXSTD 2003
E150FHLSDR 2006
E150FHLSOC 2004,2005
E150FHLSRS 2004
E150FPLSDR 2006
E150FPLSOC, E150FSLSOC 2004,2005
E150FPLSRS, E150FSLSRS 2004
E150FPLSTD, E150FPXSTD, E150FSLSTD 2003
E150FPXSDR 2006
E150FPXSOC 2004,2005
E150FPXSRS 2004
E150FSLSDR 2006
E175FCXSDS 2006
E175FCXSNF, E175FPLSNF, E175FPXSNF 2002
E175FCXSOD 2004,2005
E175FCXSRE 2004
E175FCXSSR, E175FCXSSV, E175FPLSSR, E175FPLSSV, E175FPXSSR, E175FPXSSV, E175FSLSSC, E175FSLSSV, RE175FCSSR, RE175FCSSV, RE175FLSSR, RE175FLSSV, RE175FSSC, RE175FXSSR, RE175FXSSV 2000
E175FCXSTB 2003
E175FPLSDS 2006
E175FPLSOD, E175FSLSOE 2004,2005
E175FPLSRE, E175FSLSRB 2004
E175FPLSTB, E175FPXSTB, E175FSLSTM 2003
E175FPLSTF 2003
E175FPXSDS 2006
E175FPXSOD 2004,2005
E175FPXSRE 2004
E175FSLSDD 2006
E175MFXSOS 2005
E175MFXSOS 2004
E200FCSSSC, E200FCSSSH, E200FCXSSC, E200FCXSSH 2000
E200FCXSNF 2002
E200FCXSOE 2004,2005
E200FCXSRB 2004
E200FCXSTM, E200FHLSTS 2003
E200FHLSOR 2004,2005
E200FHLSRC 2004
E200FPLSNF, E200FPXSNF 2002
E200FPLSOE, E200FPXSOE, E200FSLSOE 2004,2005
E200FPLSRB, E200FPXSRB, E200FSLSRB 2004
E200FPLSSC, E200FPLSSH, E200FSLSSC, E200FSLSSH, RE200FLSSC, RE200FLSSH, RE200FSSH 2000
E200FPLSTM, E200FPXSTM, E200FSLSTM 2003
E200FPXSSC, E200FPXSSH, RE200FXSSC, RE200FXSSH 2000
E225FCXSNF, E225FCZSNF, E225FHLSNF, E225FPLSNF, E225FPXSNF, E225FPZSNF 2002
E225FCXSOE, E225FCZSOE 2004,2005
E225FCXSRB, E225FCZSRB 2004
E225FCXSSC, E225FCXSSH, E225FCZSSC, E225FCZSSH, RE225FCSSC, RE225FCSSH 2000
E225FCXSTM, E225FCZSTM, E225FPLSTM, E225FPXSTM, E225FPZSTM 2003
E225FGLSSC, E225FGLSSH, E225FPLSSC, E225FPLSSH, RE225FGSSC, RE225FGSSH, RE225FLSSC, RE225FLSSH 2000
E225FHLSOB, E225FHXSOC 2004,2005
E225FHLSRM, E225FHXSRS 2004
E225FHLSSS, RE225FHSSS 2000
E225FHLSTA 2003
E225FPLSOE, E225FPXSOE, E225FPZSOE 2004,2005
E225FPLSRB, E225FPXSRB, E225FPZSRB 2004
E225FPXSSC, E225FPXSSH, E225FPZSSC, E225FPZSSH, RE225FXSSC, RE225FXSSH, RE225FZSSH 2000
E250FCXSNF, E250FCZSNF, E250FPZSNF 2002
E250FCXSOB, E250FCZSOB 2004,2005
E250FCXSRM, E250FCZSRM 2004
E250FCXSSS, E250FCZSSS 2000
E250FCXSTA, E250FCZSTA, E250FPLSTR, E250FPXSTA, E250FPZSTA 2003
E250FGLSSS, E250FPLSSS 2000
E250FPLSOM, E250FPXSOB, E250FPZSOB 2004,2005
E250FPLSRA, E250FPXSRM, E250FPZSRM 2004
E250FPXSNF 2002
E250FPXSSS, E250FPZSSS 2000
E75FPLSNF 2002
E75FPLSSH, RE75FPLSSH 2000
E75FPLSTA 2003
E90FPLSNF 2002
E90FPLSSH, E90FPLSSR, RE90FPLSSH, RE90FPLSSR 2000
E90FPLSTB, E90FSLSTB 2003

Information:


Illustration 1 g01234885
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF/RESET position.
Illustration 2 g01233770
Left side engine view (1) J1/P1 ECM connectors
Thoroughly inspect connectors (1) and any other connectors in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for corrosion, abrasion, and pinch points from the throttle switch to the ECM.Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The wiring and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the wiring and/or the connectors.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Remote Throttle
Ensure that the transmission is in the neutral position. Apply the parking brake. Start the scraper engine. Place the throttle for the scraper engine in the low idle position.
Connect the Caterpillar Electronic Technician (Cat ET) to the service tool connector.
Access the status for the "Remote Throttle Switch".
While you monitor the status, set the remote throttle switch to the ON position.
While you monitor the status, operate the switches for the ACCEL input and the DECEL input.Expected Result:The status for the "Remote Throttle Switch" indicates "On" when the On/Off switch is in the ON position.The status for the "Remote Throttle Accel" indicates "On" when the switch for the ACCEL input is in the ACCEL position.The status for the "Remote Throttle Decel" indicates "On" when the switch for the DECEL input is in the DECEL position.Results:
OK - The status changed accordingly.Repair: The remote throttle is operating properly at this time.Verify that the requirements for the remote throttle were met prior to the problem.If the problem is intermittent, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - There is a problem with the switch circuits. Proceed to Test Step 3.Test Step 3. Check the Switch Circuits at the Harness ConnectorNote: If all of the switches are inoperative, the problem may be caused by the return wire.
Turn the keyswitch to the OFF position.
Disconnect the harness connector.
Turn the keyswitch to the ON position.
Illustration 3 g01234934
Harness connector (07) DECEL input (08) ACCEL input (09) On/Off (NO) (10) On/Off (NC) (14) Digital return
While you monitor the status for the remote throttle, use a jumper wire to connect the following terminals to 14 (Digital return) on the harness connector:
10 (On/Off (NC))
09 (On/Off (NO))
08 (Accel)
07 (Decel)
Table 1
Status for the Remote Throttle    
Status     Terminal    
10 09     08     07    
"Remote Throttle Switch"     Off     On     (1)     (1)    
"Remote Throttle Accel"     Off     Off     On     Off    
"Remote Throttle Decel"     Off     Off     Off     On    
( 1 ) The status for "Remote Throttle Switch" will indicate "Abnormal or Incorrect Data".Expected Result:The status for the remote throttle changes according to Table 1.Results:
OK - The status for the remote throttle changes according to the Table. There is a problem between the machine connector and the switches.Repair: Connect the harness connectors. Proceed to Test Step 5.
Not OK - The status for the remote throttle does not change according to the Table. There is a problem between the machine connector and the ECM.Repair: Leave the harness connectors disconnected. Proceed to Test Step 4.Test Step 4. Check the Switch Circuits at the ECM
Turn the keyswitch to the OFF position.
Insert a 7X-1715 Adapter Cable As (40-PIN BREAKOUT) between the J1 and P1 ECM connectors.
Turn the keyswitch to the ON position.Note: The harness connectors must be disconnected.
While you monitor the status for the remote throttle switch, use a jumper wire to connect the following terminals to terminal 05 (Digital return) on the breakout T.
45 (On/Off (NC))
44 (On/Off (NO))
46 (Accel)
47 (Decel)
Table 2
Status for the Remote Throttle    
Status     Terminal    
45 44     46     47    
"Remote Throttle Switch"     Off     On     (1)     (1)    
"Remote Throttle Accel"     Off     Off     On     Off    
"Remote Throttle Decel"     Off     Off     Off     On    
( 1 )


Back to top