0323442 EVINRUDE GASKET, C case to cover


0323442 GASKET, C case to cover EVINRUDE 4806E GASKET
0323442 GASKET, C case to cover EVINRUDE
Rating:
8

Buy GASKET, C case to cover 0323442 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

4806E   EVINRUDE

BRP EVINRUDE entire parts catalog list:

4806E, 4836E, 4837E 1978

Information:


Illustration 1 g01123371
Schematic for the diagnostic lampTest Step 1. Check the Operation of the Diagnostic Lamp
Turn the keyswitch to the ON position.
Monitor the diagnostic lamp.Expected Result:The diagnostic lamp turns on for five seconds. Then, the diagnostic lamp turns off. If a diagnostic code is active, the diagnostic lamp will flash.Results:
OK - The diagnostic lamp turns on for five seconds. Then, the diagnostic lamp turns off. The diagnostic lamp appears to be operating correctly at this time.STOP
Not OK - The diagnostic lamp did not turn on for five seconds.Repair: Replace the light bulb for the diagnostic lamp. Verify that the repair resolved the problem. If the repair did not resolve the problem, proceed to Test Step 2.Test Step 2. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 2 g01146374
Left side engine view (typical example) (1) J1/P1 ECM connector
Illustration 3 g01146383
Left side engine view (typical example) (2) P61 Customer connector
Thoroughly inspect connectors (1) and (2). Inspect the connections on the diagnostic lamp. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01102224
P1 terminals that are associated with the diagnostic lamp (P1-28) Diagnostic lamp (P1-65) −Battery
Illustration 5 g01102219
J61 and P61 terminals that are associated with the diagnostic lamp (24) Diagnostic lamp
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the diagnostic lamp.
Check the allen head screw for the ECM connectors and the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasions and for pinch points from the diagnostic lamp to the ECM.Expected Result:All of the connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and the wiring are OK. Proceed to Test Step 3.
Not OK - There is a problem with a connector and/or the wiring.Repair: Repair the connector and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 3. Test the Diagnostic Lamp Circuit at the ECM Connector
Disconnect the J1/P1 connectors.
Connect a jumper wire between terminal P1-28 and engine ground.
Turn the keyswitch to the ON position and observe the diagnostic lamp.
Remove the jumper wire and observe the diagnostic lamp.Expected Result:The diagnostic lamp turned on while the jumper wire was connected. The diagnostic lamp turned off when the jumper wire was removed.Results:
OK - The diagnostic lamp turned on while the jumper wire was connected. The diagnostic lamp turned off when the jumper wire was removed. The circuit for the diagnostic lamp is functioning properly. Proceed to Test Step 6.
Not OK - The diagnostic lamp did not turn on. There is a problem with the circuit for the diagnostic lamp. Proceed to Test Step 4.Test Step 4. Test the Diagnostic Lamp Circuit at the Diagnostic Lamp
Disconnect wire F404-RD from the diagnostic lamp.
Connect a jumper wire between the diagnostic lamp's open terminal and engine ground.
Turn the keyswitch to the ON position and observe the diagnostic lamp.
Remove the jumper wire and observe the diagnostic lamp.Expected Result:The diagnostic lamp turned on while the jumper wire was connected. The diagnostic lamp turned off when the jumper wire was removed.Results:
OK - The diagnostic lamp turned on while the jumper wire was connected. The diagnostic lamp turned off when the jumper wire was removed. The +Battery side of the circuit for the diagnostic lamp is functioning properly. There is a problem with the return wire between the diagnostic lamp and the P1 connector.Repair: Repair wire F404-RD between the diagnostic lamp and P1-28. Verify that the problem is resolved.STOP
Not OK - The diagnostic lamp did not turn on when the jumper wire was connected. There is a problem with the +Battery side of the circuit for the diagnostic lamp. Proceed to Test Step 5.Test Step 5. Check the Voltage from the Keyswitch to the Diagnostic Lamp
Turn the keyswitch to the OFF position.
Remove the wire from the terminal R of the keyswitch.
Turn the keyswitch to the ON position.
Measure the voltage on terminal B of the keyswitch to engine ground.
Measure the voltage on terminal R of the keyswitch to engine ground.
Turn the keyswitch to the OFF position.Expected Result:Voltage is present on terminal B and terminal R at the keyswitch.Results:
OK - Voltage is present on terminal B and terminal R at the keyswitch.Repair: If voltage is present on terminal R, repair the wire between the keyswitch and the diagnostic lamp. Verify that the breaker is not tripped. Return all wiring to the original configuration. Verify that the problem is resolved.STOP
Not OK - Voltage is not present on terminal B at the keyswitch.Repair: If voltage is not present on terminal B, repair the wire between the +Battery and the keyswitch. Check the battery's no-load voltage. Return all wiring to the original configuration. Verify that the problem is resolved.STOP
Not OK - Voltage is not present on terminal R at the keyswitch.Repair: If voltage is present on terminal B of the keyswitch but not present on terminal R, replace the keyswitch. Return all wiring to the original configuration. Verify that the problem is resolved.STOPTest Step 6. Check the Operation of the ECM
Remove terminal P1-28.
Fabricate a jumper wire for the ECM connector.
Insert the jumper into P1-28.
Connect the J1/P1 connectors.
Connect one probe of a voltage test lamp to the jumper wire in P1-28.
Connect the other probe of the voltage test lamp to +Battery.
Turn the keyswitch to the ON position


Parts gasket EVINRUDE:

0301996
GASKET
0301996 GASKET
100193A, 100293R, 1002R, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 15404G, 15504C,
0303615
GASKET, Pump to by-pass cover
0303615 GASKET, Pump to by-pass cover
100990S, 10524C, 10624G, 10724A, 10824M, 10924B, 115790S, 115793S, 115890C, 15504C, 15604A, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A
0203130
GASKET,Cylinder head
0203130 GASKET,Cylinder head
3802A, 4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4706B, 4806E, 4902B, 4904D, E4RLCSS, E5RCSS, E8RCSS
0315338
GASKET, Lwr mtr cover to exhaust hsg, outer
0315338 GASKET, Lwr mtr cover to exhaust hsg, outer
4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4706B, 4806E, 4902B, 4904D, E4RLCSS, E4WCIC, E4WCNR
0319011
 
0319011 GASKET, Float bowl
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 4806E, 4904D, E10ECDB, E10ECOM, E10ECSE, E10ELCID, E10ELCNS, E10ELCRA, E10ELCTC, E15ECDE, E15ECIS, E15ECNC, E15ECOB, E15ECRM, E15ECSD, E15ECTR, E4BRHCNR, E4BRHCOB, E4BRHCRM, E4BR
0323452
 
0323452 GASKET
4806E, 4904D, BE3REDS, BE4BREDS, BE4BREUC, BE4RDHEDS, E3BRCEC, E3BRESR, E3RCCM, E3RCUA, E3REIA, E3RENM, E3REOD, E3RERE, E3RETB, E3REUC, E4BRCICI, E4BRECRJ, E4BRHCCS, E4BRHCDE, E4BRHCNR, E4BRHCOB, E4BRHCRM, E4BRHCTA, E4BRHCUD, E4RCCS, E4RCEC, E4RCUD,
0323445
GASKET, Cover plate
0323445 GASKET, Cover plate
4806E, 4904D, BE3REDS, BE4BREDS, BE4BREUC, BE4RDHEDS, E3BRCEC, E3BRESR, E3REIA, E3RENM, E3REOD, E3RERE, E3RETB, E3REUC, E4BRCICI, E4BRECRJ, E4BRHCCS, E4BRHCDE, E4BRHCNR, E4BRHCOB, E4BRHCRM, E4BRHCTA, E4BRHCUD, E4RDHCCS, E4RDHCDE, E4RDHCEC, E4RDHCUD,
Back to top