0334113 EVINRUDE GASKET, Inner exh. hsg. to megaphone

Table 1
J1939 Code and Description CDL Code and Description Comments
110-0
Engine Coolant Temperature : High - most severe (3) E361 (1)
High Engine Coolant Temperature The code is logged.
110-15
Engine Coolant Temperature : High - least severe (1) E361(2)
High Engine Coolant Temperature The code is logged.
Engine power is derated.
110-16
Engine Coolant Temperature : High - moderate severity (2) E361(3)
High Engine Coolant Temperature The code is logged.
If the ground speed of the vehicle is zero and the parking brake is set, the engine will be shut down. Probable Causes
Diagnostic Codes and Event Codes
Low coolant level
Radiator
Coolant leak
Engine cooling fan
Pressure cap for the radiator
Temperature Control Module (TCM)
Jacket water pump
Engine overloadRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Determine if the event code that directed to this story is present.
C. Look for active diagnostic codes that are associated with the system for the event code that directed to this story.
Codes
Result: An associated code is present.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A 110–0, 110–15, or 110–16 code is present.
Proceed to the next step.
Result: No active codes
STOP
2. Low Coolant Level
A. Inspect the coolant level.
Coolant
Result: The coolant level is OK.
Proceed to the next step.
Result: The coolant level is NOT OK.
Repair: Add coolant
If the problem is not resolved, proceed to the next step.
3. Radiator
A. Check the cooling fins on the radiator for dirt and/or for debris.
B. Check the cooling fins on the radiator for damage.
C. Check the radiator for internal blockage. Check the temperature difference between the inlet and the outlet of the radiator.
Radiator
Result: The cooling fins are clean.
Continue with this step.
Result: The cooling fins are not clean.
Repair: Remove dirt and/or debris.
Result: The cooling fins are damaged.
Repair: Refer to the Systems Operation/Testing and Adjusting manual for instructions for testing and inspecting the cooling system.
Result: The cooling fins are not damaged.
Continue with this step.
Result: The radiator has an internal blockage.
Repair: Clean the radiator or perform the necessary repairs.
Result: The radiator does not have an internal blockage
If the problem is not resolved, proceed to the next step.
4. Coolant Leak
A. Check the cooling system for leaks.
1. Inspect the coolant for presence of bubbles.
Note: Cavitation will reduce the efficiency of the cooling system.
2. Check the cooling system for combustion gases.
Leak
Result: The cooling system is OK.
Proceed to the next step.
Result: The cooling system is NOT OK.
Repair: Or replace as necessary.
If the problem is not resolved, proceed to the next step.
5. Engine Cooling Fan
A. Check for proper operation of the cooling fan.
Fan
Result: The cooling fan is OK.
Proceed to the next step.
Result: The cooling fan is not OK.
Repair: Repair or replace as necessary.
If the problem is not resolved, proceed to the next step.
6. Pressure Cap for the Radiator
A. Check operation of the pressure relief valve and the radiator cap.
Relief Valve
Result: The pressure relief valve is OK.
Result: The pressure relief valve is NOT OK.
Repair: If necessary, clean the seal and the seating surface in the cap. Check that the seating surface on the fill neck of the radiator is clean and undamaged. If the sealing components of the pressure cap are suspect, replace the cap.
Illustration 1 g01320751
Connector locations for the temperature control module
(1) 8-pin connector for the motor assembly and the communications device
(2) 12-pin connector for the engine harness
Illustration 2 g02554619
Removing the inspection cover from the motor assembly
(3) Main shaft extension
(4) Plug and O-ring seal
Illustration 3 g01321224
Table 3
Troubleshooting Test Steps Values Results
7. Temperature Control Module
A. Perform the following procedure:
1. Visually inspect the wiring from the TCM to the coolant temperature sensor and from the temperature control module to the power supply. Visually inspect the 12-pin connector and the 8-pin connector at the temperature control module. Check for a tight connection at the connectors.
B. Check for proper operation of the electronic fluid temperature control:
1. Ensure that the keyswitch is in the OFF position. Turn the electrical disconnect to the OFF position.
2. Remove cover bolts (4) from the motor assembly. Remove the inspection cover from the motor.
3. Use the appropriate wrench to rotate the main shaft extension. Ensure that the shaft rotates freely. Rotate the shaft to ensure that the piston is not positioned at one of the ends stops of the valve.
4. Visually inspect main shaft extension (3) for rotation while you establish power to the ECM and to the keyswitch circuit. The shaft will rotate several times during the powerup sequence.
5. During the power-up sequence, listen for the valve to travel to the end stop. Listen for the piston to hammer the end stop to establish the valve position.
6. With the electrical disconnect in the ON position, disconnect the engine harness connector (12-pin connector) at the controller. Diagnostic codes related to the valve will be activated.
7. Use a wrench to rotate the main shaft extension to position the valve piston away from the end stop