0316504 GEAR, Reverse EVINRUDE
18102S, 18202R, 18304A, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25904R
GEAR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$52.00
08-05-2022
0.0[0.00] Pounds
-: -
"Amphenol RF 031-6504 Conn; RF; TNC; Rt.Angle; CablePlug; 50Ohm; LMR-200; IP67, ReversePolarity; Solder/Crimp"
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE » 0316504
18304A, 18305A 1973
25102S, 25103S 1971
25202R, 25203R, 25252R, 25253R 1972
25302A, 25303A, 25352A, 25353A 1973
25402M, 25403M, 25452M, 25453M 1974
25502B, 25503B, 25552B, 25553B 1975
25602E, 25603E, 25652E, 25653E 1976
25702H, 25702S, 25703H, 25703S, 25752H, 25752S, 25753H, 25753S, 35702C, 35702H, 35703C, 35703H, 35752C, 35752H, 35753C, 35753H 1977
25802C, 25803C, 25852C, 25853C, 35802R, 35803R, 35852R, 35853R 1978
25904R, 25905R, 25952R, 25953R, 35902A, 35903A, 35952A, 35953A 1979
Information:
Typical Example1. Remove cover (1) and covers (2).
Typical Example2. Remove louver (3) and cover (4).
Typical Example
Typical Example3. Put a piece of cardboard (5) between stator (6) and rotor assembly (7). This step is necessary to prevent damage to the rotor assembly and stator when the generator fan is disconnected from the flywheel housing.
Typical Example4. Loosen three bolts and nuts (8) on the front engine support.
Typical Example5. Remove the bolts that hold the generator in place on the base. G3412 Engines do not have mounts, sleeves or collars. G3412 Engines have four bolts that hold the generator set to the base.6. Fasten a strap (9) and Tool (A) to the generator as shown. Fasten a chain to the lifting bracket on the front of the generator.7. Lift the generator and the rear of the engine enough to install blocks (10) under the flywheel housing. Lower the generator and engine until the weight of the engine is on blocks (10).
Typical Example8. Remove bolts (12) that hold fan (13) against the flywheel housing. Remove bolts (11) that hold the generator housing against the flywheel housing.9. Remove the generator from the engine. The weight of the generator is approximately 1134 kg (2500 lb).
Typical Example10. Remove bolts (14) and plates (15).
Typical Example11. Remove fan (16) and shims (17).Install Generator
Typical Example1. Put fan (1) in position in the generator housing. Make sure holes (2) are toward the outside as shown.2. Install a 1/2 -10 NC × 101 mm (4 in) Long Guide Bolt (4) in the generator hub.3. Check the thickness of the plates that are installed over shims (3). The thickness of shims (3) and the plates must be 12.116 0.406 mm (.4770 .1600 in). Add or subtract shims (3) to get the correct thickness.
Typical Example5. Install plates (5) on the hub. Remove the guide bolt and install the bolts that hold the shims and plates in position.
Typical Example6. Remove the cover from the flywheel housing and install Tool (B).
Typical Example G3412 Engines do not have mounts (8).7. Install a 5/8 -11 NC × 101 mm (4 in) Long Guide Bolt in the flywheel.8. Fasten Tool (A) and straps (6) to the generator as shown. Fasten a chain to the lifting bracket on the generator. Put generator (7) in place on the engine. The weight of the generator is approximately 1133 kg (2500 lb). Use Tool (B), if necessary, to put the guide bolt in the flywheel housing in alignment with the holes in the plates and fan on the generator.
Typical Example9. Install bolts (10) that hold fan (9) in position on the flywheel. Remove the guide bolt and install the bolt.10. Install the bolts that hold the generator housing to the flywheel housing.
Typical Example11. Lift the generator and engine enough to remove blocks (11). Lower the generator and engine down on to mounts (8).12. Install the four bolts that hold the generator in place on the base.
Typical Example13. Tighten bolts (17) on the engine front support.
Typical Example14. Remove cardboard (18) from between the rotor assembly and the stator.
Typical Example15. Install louver (19) and cover (20).
Parts gear EVINRUDE:
0377631
0377631 GEAR & SHAFT, Short
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B
0377943
0377943 GEAR & SHAFT, Long
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25902B, 35602G, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6802A, 6902M
0384864
0384864 GEAR, Throttle control
18102S, 18202R, 18304A, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E
0384566
0384566 GEAR & BUSHING, Forward
18102S, 18202R, 18304A, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H
0387634
0387634 GEAR, Throttle control
25702H, 25802C, 25904R, 35602G, E25CNE, E25ECIB, E25ECTD, E25RCSA, E25RSA, E25RSLS, E35ECIG, E35ECND, E35ECSM, E35ECTS
0387057
0387057 GEAR & SHAFT, Short
25702H, 25802C, 25904R, 35602G, E20CRCOS, E25CNE, E25ECIB, E25ECOC, E25ECRS, E25ECTD, E25RCSA, E25RSA, E25RSLS, E25RWCOS, E25RWCRD, E30ECOA, E30ECRR, E35ECIG, E35ECND, E35ECRR, E35ECSM, E35ECTS
0322080
0388125
0388125 GEAR & BUSHING ASSY.,Fwd.
25702H, 25802C, 25904R, E25RCSA, E35ECIG, E35ECND, E35ECSM, E35ECTS