0384566 EVINRUDE GEAR & BUSHING, Forward


0384566 GEAR & BUSHING, Forward EVINRUDE 18102S, 18202R, 18304A, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H GEAR
0384566 GEAR & BUSHING, Forward EVINRUDE
Rating:
13

Buy GEAR & BUSHING, Forward 0384566 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$147.00
 

23-04-2020

-: -
OMC Forward Gear P/N 384566 0384566 NOS (Part of P/N 390972)
Number on catalog scheme: 33
 

BRP EVINRUDE entire parts catalog list:

18102S, 18103S 1971
18202R, 18203R 1972
18304A, 18305A 1973
25102S, 25103S 1971
25202R, 25203R, 25252R, 25253R 1972
25302A, 25303A, 25352A, 25353A 1973
25402M, 25403M, 25452M, 25453M 1974
25502B, 25503B, 25552B, 25553B 1975
25602E, 25603E, 25652E, 25653E 1976
25702H, 25702S, 25703H, 25703S, 25752H, 25752S, 25753H, 25753S, 35702C, 35702H, 35703C, 35703H, 35752C, 35752H, 35753C, 35753H 1977

Information:


Illustration 1 g00285581
(1) Valve. (2) Clip retainers. (3) Foam. (4) Elbow. (5) Gasket. (6) Baffle.
The crankcase breather removes the combustion gases from the engine crankcase. The crankcase breather directs the gases to the induction system.An internal port in the rocker cover allows the gases in the crankcase to pass into the breather body through foam (3). The gases flow through a series of baffles (6) and into the valve cover through holes at the bottom of the chamber for the baffles. Valve (1) controls the flow of gases which pass from the breather through the plastic outlet elbow (4) to the intake manifold.The valve cover and the breather assembly are made of a composite material. The valve cover and the breather assembly should be removed and installed with care.Disassembly
Do not use excessive force to remove the hose from the breather outlet elbow. If the breather outlet elbow breaks away from the breather body, see the procedure to repair the connection for the breather outlet elbow.
Release the hose clamp and carefully remove the hose from elbow (4).
Remove the valve cover. Refer to the Service Manual for more information.
Use care not to damage the breather cover or the breather body with a pry bar.
Remove the bolts and carefully remove the breather cover from the breather body. It may be necessary to use a suitable pry bar in order to remove the breather cover from the breather body. Ensure that the pry bar does not damage the breather cover or the breather body. Gasket (5) should be removed and discarded.
Release clip retainers (2) on valve (1). Push valve (1) out of the breather cover.
Foam (3) should be removed and discarded.
To prevent damage to the breather valve, remove the breather valve before the cover is washed.
Ensure that all the cleaning fluid is removed before the breather is assembled.
Use a clean nonflammable solvent to wash the body of the breather, the cover, baffle (6), and elbow (4). Thoroughly dry the components after cleaning the components.
Ensure that the holes in the bottom of the chamber for baffles (6 ) are not restricted. If necessary, clean the holes. Assembly
Install baffles (6) into the grooves in the breather body.
Install a new foam (3) into the breather body.
Install a new valve (1) into the breather cover. Ensure that clip retainers (2) are engaged correctly.
Install a new gasket (5). The gasket is installed dry. Put the cover and valve assembly into position on the breather body. Loosely install the bolts. Tighten the bolts gradually and tighten the bolts evenly to a torque of 3 N m (27 lb in).
Do not use excessive force to fit the hose to the breather outlet elbow.
Ensure that there is no restriction in elbow (4) or in the breather hose. Carefully install the breather hose on elbow (4). Tighten the hose clamps that fasten the hose to the elbow. Procedure to Repair the Connection for the Outlet Elbow of the Breather
Thoroughly clean the inside of the breather body after it has been drilled.
Ensure that the breather body is secure. Use a 22.5 mm (0.89 inch) drill in order to drill to a depth of 10.0 mm (0.39 inch). Drill the depth in order to remove the broken connection of the outlet elbow. Thoroughly clean the inside of the breather body.
Thoroughly clean the contact faces of the elbow and the breather cover.
Install elbow (4). Ensure that the contact surface of the connection for the elbow has a rough finish. Put the elbow into position on the breather body.
Apply Permabond® E3524 adhesive in accordance with the OEM instructions in order to secure the elbow to the breather body.


Parts gear EVINRUDE:

0377631
GEAR & SHAFT, Short
0377631 GEAR & SHAFT, Short
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B
0377943
 
0377943 GEAR & SHAFT, Long
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25902B, 35602G, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6802A, 6902M
0384864
GEAR, Throttle control
0384864 GEAR, Throttle control
18102S, 18202R, 18304A, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E
0316504
GEAR, Reverse
0316504 GEAR, Reverse
18102S, 18202R, 18304A, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25904R
0387634
GEAR, Throttle control
0387634 GEAR, Throttle control
25702H, 25802C, 25904R, 35602G, E25CNE, E25ECIB, E25ECTD, E25RCSA, E25RSA, E25RSLS, E35ECIG, E35ECND, E35ECSM, E35ECTS
0387057
 
0387057 GEAR & SHAFT, Short
25702H, 25802C, 25904R, 35602G, E20CRCOS, E25CNE, E25ECIB, E25ECOC, E25ECRS, E25ECTD, E25RCSA, E25RSA, E25RSLS, E25RWCOS, E25RWCRD, E30ECOA, E30ECRR, E35ECIG, E35ECND, E35ECRR, E35ECSM, E35ECTS
0322080
GEAR,Reverse
0322080 GEAR,Reverse
25702H, 25802C, 25904R, E25RCSA, E35ECIG, E35ECND, E35ECSM, E35ECTS
0388125
GEAR & BUSHING ASSY.,Fwd.
0388125 GEAR & BUSHING ASSY.,Fwd.
25702H, 25802C, 25904R, E25RCSA, E35ECIG, E35ECND, E35ECSM, E35ECTS
Back to top