5004991 EVINRUDE *GEAR SET, Fwd, Rev, Pinion


5004991 *GEAR SET, Fwd, Rev, Pinion EVINRUDE E135FCXSNF, E150FCXSNF, E175FCXSNF GEAR
5004991 *GEAR SET, Fwd, Rev, Pinion EVINRUDE
Rating:
68

Buy *GEAR SET, Fwd, Rev, Pinion 5004991 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$425.95
 

23-08-2023

-: -
Lower Unit Gear Set, 2002-2008 Evinrude E-Tec M1, 135, 150, 200, 225, and 250 hp Outboards 5001582
$499.95
 

23-08-2023

-: -
Lower Unit Gear Set, 2002-2008 Evinrude E-Tec M1, 135, 150, 200, 225, and 250 hp Outboards 5001582
Number on catalog scheme: 43
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E135FCXSNF, E135FPLSNF, E135FPXSNF 2002
E150FCXSNF, E150FPLSNF, E150FPXSNF 2002
E175FCXSNF, E175FPLSNF, E175FPXSNF 2002

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01310618
Typical example
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove bolts (1) and remove the assembly of cover (2) , spring (3) and diaphragm (4) . Note the orientation of cover (2) .
Remove spring (3) and diaphragm (4) from cover (2) .
Remove adapter (5) and joint (6) from valve mechanism cover (7) .Note: Make a temporary mark in order to show the orientation of the adapter for installation.
If necessary, follow Steps 4.a through 4.c in order to remove the gauze for the breather.
Remove valve mechanism cover (7) . Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Remove screws (9) and carefully remove plate (10) .
Remove gauze (8) from valve mechanism cover (7) .Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Loctite 594        
B     247-5377     Torque Wrench     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Make sure that the components of the breather assembly are installed correctly. Engine damage may occur if the breather assembly is not working properly.
Illustration 2 g01310618
Typical example
Clean all parts and inspect all parts. Replace any parts that are worn or damaged. Ensure that the cavity for the breather in the valve mechanism cover is clean. Ensure that vent hole in adapter (5) and the vent hole in cover (2) are free from restriction.
If necessary, follow Steps 2.a through 2.e in order to install the gauze for the breather.
Install gauze (8) to valve mechanism cover (7) .
Apply a bead of Tooling (A) to the mating surface of the plate on valve mechanism cover (7) .
Position plate (10) on valve mechanism cover (7) and install screws (9) .
Tighten screws (9) to a torque of 1.5 N m (13 lb in).
Install valve mechanism cover (7) . Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Position a new joint (6) on the valve mechanism cover and install adapter (5) .Note: Ensure the correct orientation of the adapter. The vent hole should face upward.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Install diaphragm (4) and spring (3) to cover (2) .
Position the assembly of cover (2) , spring (3) and diaphragm (4) onto valve mechanism cover (7) .Note: Ensure the correct orientation of the cover.
Install bolts (1) . Use Tooling (B) in order to tighten bolts to a torque of 3 N m (27 lb in).


Parts gear EVINRUDE:

0342881
 
0342881 GEAR, Drive, starter
E100FPLSOC, E100FPLSRS, E115FPLEEC, E115FPLSDS, E115FPLSIF, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSSH, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLECS, E115FSLSDS, E135FCXSDE, E135FCXSIF, E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSSS
0342880
GEAR, Pinion & shaft
0342880 GEAR, Pinion & shaft
E100FPLSOC, E100FPLSRS, E115FPLEEC, E115FPLSDS, E115FPLSIF, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSSH, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLECS, E115FSLSDS, E135FCXSDE, E135FCXSIF, E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSSS
5004995
 
5004995 *GEAR SET Assy
E135FCXSNF, E135FCXSRM, E135FCXSTA, E135FPLSTA, E135FSLSTA, E150FCXSNF, E150FCXSRS, E150FCXSTD, E150FPLSTD, E175FCXSNF, E175FCXSRE, E175FCXSTB, E175FPLSTB
5004994
 
5004994 **GEAR SET, Fwd, Rev, Pinion
E135FCXSNF, E150FCXSNF, E175FCXSNF
Back to top