0398191 EVINRUDE GEARCASE & BEARING ASSY.


0398191 GEARCASE & BEARING ASSY. EVINRUDE C155WTLM, E155WTLCUA, E155WTLESM, E155WTLZ GEARCASE
0398191 GEARCASE & BEARING ASSY. EVINRUDE
Rating:
83

Buy GEARCASE & BEARING ASSY. 0398191 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$639.79
 

21-09-2021

-: -
K&M 039-8191 Fabric JD 6000-7000 Series Instructional Seat
Tough Brown Skin covering || Durable vacuum formed cushions for long wear || Seat cushion folds up for a folded width of 5" || Stable mounting || Seat belt and brackets included for added safety
Number on catalog scheme: 1
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

C155WTLM, C155WTXM 1988
E155WTLCUA, E155WTXCUA 1987
E155WTLESM, E155WTXESM 1990
E155WTLZ, E155WTXZ 1989

Information:

Complete the procedure in the order in which the steps are listed.Probable causes
Diagnostic codes
High exhaust temperature
Exhaust systemNote: The procedures have been listed in order of probability. Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Turn the keyswitch to the ON position. Do not start the engine.
B. Connect to the electronic service tool.
C. Check for associated diagnostic trouble codes.
Diagnostic trouble codes
Result: A 4360 code is active or recently logged.
Proceed to Test Step 2.
Result: An associated code other than 4360 is active or recently logged.
Repair: Troubleshoot the logged or active code. Refer to Troubleshooting, "Diagnostic Trouble Codes".
Result: No codes are active or recently logged.
Proceed to Test Step 5.
2. Check the Operation of the SCR Catalyst Inlet Temperature Sensor
Note : Only perform this step on a cold engine.
A. Remove the SCR catalyst inlet temperature sensor and allow the sensor to rest in ambient air for 2 minutes.
B. Connect the electronic service tool to the diagnostic connector.
C. Monitor the value of the SCR catalyst inlet temperature sensor on the electronic service tool.
Sensor
Result : The value of the SCR catalyst inlet temperature sensor is within 9° C (15° F) of ambient temperature.
Repair : Reinstall the sensor. torque the sensor to the proper specification.
For a 4360-16 code proceed to Test Step 3.
For a 4360-17 or 4360-18 code proceed to Test Step 4.
Result : The value of the SCR catalyst inlet temperature sensor is not within 9° C (15° F) of ambient temperature.
Repair : Replace the SCR catalyst inlet temperature sensor. Refer to the Disassembly and Assembly manual for more information.
Proceed to Test Step 5.
3. Check for Cause of High Temperature
A. Check for evidence of an exothermic event in the DOC and DPF.
B. Check for evidence of excessive fuel reaching the DOC or DPF
High temperature
Result: There has been an exothermic event in the DOC or DPF.
Repair: Replace the Clean Emissions Module (CEM).
Result: There is evidence of excessive fuel reaching the DOC or DPF.
Repair: Investigate the cause of the excess fuel.
4. Check the Exhaust System
A. Check the exhaust system for gas leaks between the turbocharger and the exhaust tail pipe.
B. Check for gas leaks around the following items in the Clean Emissions Module (CEM):
Temperature sensors
SCR intake NOx sensor
DEF injector
C. Check for missing or damaged exhaust system insulation.
D. Make sure that the cooling air flow over the CEM is not excessive for the ambient conditions.
Exhaust System
Result: The exhaust system or the CEM has a gas leak.
Repair: Make the necessary repairs.
Proceed to Test Step 5.
Result: The exhaust system insulation is damaged or missing.
Repair: Make the necessary repairs.
Proceed to Test Step 5.
Result: There is excessive cooling air flow over the CEM.
Repair: Reduce the cooling air flow. If necessary, consult the Dealer Solutions Network (DSN) for further advice.
Proceed to Test Step 5.
5. Inspect the DPF
A. Inspect the inlet of the DPF. Inspect the DPF for a damaged or missing DPF core.
Damaged DPF core
Result: The DPF has a damaged or missing DPF core.
Repair: Repair the damaged DPF or missing DPF core. Proceed to Test Step 6.
6. Check the SCR Catalyst Temperature
A. Connect to the electronic service tool.
B. Run the engine.
C. Perform the "Manual Hydrocarbon Dosing Capability Test".
Manual hydrocarbon dosing capability test
Result: The "Manual Hydrocarbon Dosing Capability Test" completed successfully.
Return the unit to service.
Result: The "Manual Hydrocarbon Dosing Capability Test" failed. An error identifier is generated by the electronic service tool.
Repair: Troubleshoot the error identifier. Refer to Troubleshooting, "Service tool Error Identifiers". Repeat Test Step 4.
Result: The "Manual Hydrocarbon Dosing Capability Test" failed. No error identifiers are generated.
Contact the Dealer Solutions Network (DSN).


Parts gearcase EVINRUDE:

0396353
GEARCASE SEAL KIT
0396353 GEARCASE SEAL KIT
C155WTLM, CE275TLCDC, CE300TLCDC, E100WMLCDR, E100WMLCOC, E100WTLCUA, E100WTLESM, E100WTLZ, E120TLCCA, E120TLCEM, E120TLCOS, E120TLEIE, E120TLESB, E140CXCCS, E140CXCEC, E140CXEIA, E140CXESR, E140TLCOS, E150CXCCA, E150CXCEM, E150CXEIE, E150CXESB, E150
0398132
 
0398132 GEARCASE ASSY., Complete
C155WTLM, E155WTLCUA, E155WTLESM, E155WTLZ
0398133
 
0398133 GEARCASE ASSY., Complete
C155WTLM, E155WTLCUA, E155WTLESM, E155WTLZ
Back to top