0432810 EVINRUDE GEARCASE & BRG. ASSY.

Table 1
Diagnostic Trouble Codes
J1939 Diagnostic Code and Description Comments
5580-17
Engine Filtered Fuel Delivery Absolute Pressure : Low - least severe (1) The code is logged.
5580-18
Engine Filtered Fuel Delivery Absolute Pressure : Low - moderate severity (2) The code is logged.
The engine power is derated.
The Electronic Control Module (ECM) will illuminate the action lamp.
Table 2
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
5584-15 E390 (1)
5584-16 E390 (2)
Table 3
Troubleshooting Test Steps Values Results
1. Determine the Code
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Determine if a diagnostic trouble code is present or an associated code is present.
Codes
Result: A 5580 code is present.
Proceed to Test Step 2.
Result: An associated code is present.
Repair: Troubleshoot the associated code. Refer to the proper troubleshooting procedure.
2. Check the Fuel Level in the Tank
A. Visually inspect the fuel level in the fuel tank. Ensure that the fuel tank contains enough fuel in order to operate the engine.
B. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Fuel Level
Result: The fuel level is OK.
Proceed to Test Step 3.
Result: The fuel level is not OK.
Repair: Fill the tank. Verify that the problem has been resolved.
If the problem is not resolved, proceed to Test Step 3.
3. Inspect the Fuel System for Leaks
A. Perform a visual inspection of the fuel system. Verify that there are no fuel leaks. Inspect the fuel lines from the fuel transfer pump to the secondary fuel filter base for restrictions. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
Leaks in the Fuel System
Result: No leaks were found.
Proceed to Test Step 4.
Result: Leaks were found in the fuel system.
Repair: Repair the leaks. Verify that the problem is resolved.
If the problem is not resolved, proceed to Test Step 4.
Note: Cold weather adversely affects the characteristics of the fuel. Refer to the engine Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
Table 4
Required Tooling for Fuel Pressure Sensor
8t-7860 Connector
110-6349 Fitting As
8t-0855 Pressure Gauge
6v-3990 Coupler
Illustration 1 g03758136
C9.3 Engines
(1) Fuel temperature sensor
(2) Unfiltered fuel pressure sensor
(3) Fuel pressure sensor
(4) Fuel filter baseNote: Do not use location (2) for measuring the fuel pressure. Follow the steps below.
Table 5
Troubleshooting Test Steps Values Results
4. Check the Fuel Pressure Sensor
A. Record the fuel pressure from Cat ET. Record the value in Table 6.
B. Remove the fuel pressure sensor .
C. Install a 8t-7860 Connector into the port of the pressure sensor .
D. Install the 110-6349 Fitting As onto the 8t-7860 Connector.
E. Install a 8t-0855 Pressure Gauge onto a 6v-3990 Coupler.
F. Install the 6v-3990 Coupler onto the 110-6349 Fitting As.
G. Record the fuel pressure from Cat ET and on the pressure gauge. Record the data in Table 6.
Pressure Sensor
Result: The gauge value of the fuel pressure is within 69 kPa (10 psi) of the fuel pressure reading shown in ET.
Proceed to Test Step 5.
Result: The gauge value of the fuel pressure is not within 69 kPa (10 psi) of the fuel pressure reading shown in ET.
Repair: Replace the pressure sensor. Verify that the problem has been resolved.
If the problem is not resolved, proceed to Test Step 5.
Table 6
Engine RPM Fuel pressure from Cat ET Fuel pressure from the mechanical gauge
800
1800
Table 7
Troubleshooting Test Steps Values Results
5. Replace the Fuel Filters
A. Replace the primary filter, the secondary filter, and the tertiary fuel filters.
The fuel system will need to be primed after the filters are replaced.
B. Reset all active codes by cycling the keyswitch to the Off position for 2 minutes.
Fuel Filters
Result: The problem has been resolved.
Return the engine to service.
Result: The problem has not been resolved.
Proceed to Test Step 6.
6. Check for Air in the Fuel System
A. Check for air in the fuel. Refer to Systems Operation/Testing and Adjusting, "Air in Fuel - Test" for the proper procedure
Air in the System
Result: Air is in the system.
Repair: Refer to Systems Operation/Testing and Adjusting, "Air in Fuel - Test" for the proper