0300454 EVINRUDE GROMMET, Ignition lead

Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
444-5 Starter Motor Relay : Current Below Normal     The output driver is off for at least 5 seconds. The ECM detects an open in the circuit for the starting motor solenoid for more than 5 seconds.     The code is logged.
The alarm output is activated.    
444-6 Starter Motor Relay : Current Above Normal     The output driver is on for at least 5 seconds. The ECM detects a short in the circuit for the starting motor solenoid for more than 5 seconds.     The code is logged.
The alarm output is activated.
The output driver automatically resets and the output driver continues to try to activate the circuit component.    The engine ECM contains the logic and the outputs for starting the engine. The logic for starting the engine is customer programmable. The logic responds to inputs from the following components: engine control switch, emergency stop switch, remote start switch, data link and other inputs.The ECM also has outputs that are used for communicating the engine current state of operation. One of the outputs sends a signal in order to indicate that the engine crank terminate speed has been achieved. Another output sends a signal that indicates that the engine is running. Both of these outputs are low side ECM drivers. The power for the circuits is provided at the electrical component and the ground circuit is provided by the ECM. Refer to Troubleshooting, "Indicator Lamp - Test" for information that is related to troubleshooting these circuits.The most likely causes of any of these diagnostic codes are a poor electrical connection or a problem in a wiring harness. The next likely cause is a problem with one of the solenoids that are related to the code. The least likely cause is a problem with the ECM.The ECM supplies +Battery voltage to the starting motor solenoid when the logic determines that start-up is needed. The ECM removes the voltage when the crank terminate relay is energized. The voltage is also removed if the customer programmable "Overcrank Time" has expired.If the engine is equipped with prelubrication, start-up may not be enabled until the prelube cycle is complete. If there is a problem with the prelubrication system, the start command may not be generated. Check that the engine is receiving sufficient oil pressure during the prelube cycle. Refer to Systems Operation/Testing and Adjusting for more information on the engine air starting system.
Illustration 1 g01760670
Schematic for the components of the engine starting systemTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01760975
Location of the ECM connectors for the engine starting system (typical left side engine view) (1) J2/P2 ECM connectors (2) Control harness connectors
Illustration 3 g01413257
Location of the harness connector for the starting motor solenoid (right rear engine view) (3) Harness connector for the starting motor solenoid
Thoroughly inspect connectors (1) , (2) , and (3) . Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 4 g01413263
Terminal locations at the P2 ECM connector that are associated with the engine starting system (P2-10) Starting motor solenoid (P2-20) Return
Illustration 5 g01760993
Terminal locations at the control harness connector that are associated with the engine starting system (Terminal c) Starting motor solenoid (Terminal d) Return
Illustration 6 g01155187
Terminal locations at the harness connector for the starting motor solenoid (1) Starting motor solenoid (2) Return
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the engine starting system.
Check the allen head screw for each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the wiring harnesses for abrasion, for corrosion and for pinch points.Expected Result:All connectors, pins, and sockets are coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are coupled. Verify that the problem is resolved.STOPTest Step 2. Check for Active Diagnostic Codes
Turn the engine control switch to the OFF/RESET position. Remove the electrical power from the engine.
Connect Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Restore the electrical power to the engine. Turn the engine control to the STOP position.Note: The 444-5 Starter Motor Relay : Current Below Normal can only be detected when the output for the start command is off. The output is normally off when the engine control switch is in the STOP position. The output is also normally off or when the output for the crank terminate relay is activated.Monitor the active diagnostic code and the logged diagnostic codes on Cat® ET. Wait at least 30 seconds in order for diagnostic codes to become active.
Turn the engine control to the START position. Attempt to start the engine.Note: The 444-6 Starter Motor Relay : Current Above Normal can only be detected when the output for the start command is on. The output is normally on when the engine control is switched from the STOP position to the START position. The output remains on during engine cranking.Monitor the active diagnostic code and the logged diagnostic codes on Cat ET. Wait at least 30 seconds in order for diagnostic codes to become active.
Turn the engine control to the STOP position.