0511388 EVINRUDE GROMMET


0511388 GROMMET EVINRUDE 150840S, 175740S, 200640S GROMMET
0511388 GROMMET EVINRUDE
Rating:
18

Buy GROMMET 0511388 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

150840S, 150849S, 175840C, 175840S, 200840R, 200849R, 235840R, 235849R 1978
175740S, 175749S, 200740C, 200749C 1977
200640S, 200649S 1976

Information:

Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Operation and Maintenance Manual, "Torque Specifications" topic (Maintenance Section) for more information on the proper torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Operation and Maintenance Manual, "Torque Specifications" topic (Maintenance Section) for more information on the proper torques. Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to the Operation and Maintenance Manual, "Cooling System Specifications" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Run the engine at high idle for one minute in order to purge the air from the cavities of the engine block. Stop the engine.
Check the coolant level. Maintain the coolant level within 13 mm (0.5 inch) below the bottom of the pipe for filling. Maintain the coolant level within 13 mm (0.5 inch) to the proper level on the sight glass (if equipped).
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap and install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts grommet EVINRUDE:

0305145
GROMMET
0305145 GROMMET
100193A, 100293R, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 65832
0314008
GROMMET, Water tube
0314008 GROMMET, Water tube
100990S, 115790S, 115890C, 150840S, 150940C, 175740S, 200640S, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE1
0510905
 
0510905 GROMMET
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 55642E, 55772D, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642
0510906
 
0510906 GROMMET, Control box
150840S, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 55642E, 55772D, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D
0316354
GROMMET, Motor cover
0316354 GROMMET, Motor cover
100293R, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 15404G, 15504C, 15604A, 175740S, 200640S, 25904R, 50172S, 5
0320943
GROMMET,Impeller housing
0320943 GROMMET,Impeller housing
100990S, 115790S, 115890C, 150840S, 150940C, 175740S, 200640S, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CX
0320834
 
0320834 GROMMET
150840S, 150940C, 175740S, 200640S, C155WTLM, E150ANCRS, E150CXCCA, E150CXCEM, E150CXEIE, E150CXESB, E150STLCCA, E150STLCDC, E150STLCEM, E150STLCOH, E150STLCTE, E150STLCUR, E150STLEIE, E150STLESB, E150TLCDC, E150TLCOS, E150TLCRD, E150TLCUR, E150TRLCI
Back to top