0342618 EVINRUDE GUIDE TUBE

Illustration 1 g01440729
Typical example
(1) Clamp
Illustration 2 g01440730
Typical example of a turbocharger with a wastegate
(1) Clamp
(2) Wastegate (1) Clamps To tighten clamps (1) on the turbocharger, use the following procedure:
Tighten the clamp. Tighten the clamp to the following torque. ... 14 1 N m (10.3 0.7 lb ft)
Gently tap the clamp with a soft faced hammer.
Again tighten the clamp. Tighten the clamp to the following torque. ... 14 1 N m (10.3 0.7 lb ft) (2) Wastegate Opening pressure of the wastegate ... 138 kPa (20 psi)
Illustration 3 g01440731
Typical example
(1) Clamp
Illustration 4 g01440732
Typical example of a turbocharger with a wastegate
(1) Clamp
(2) Wastegate (1) Clamps To tighten clamps (1) on the turbocharger, use the following procedure:
Tighten the clamp. Tighten the clamp to the following torque. ... 14 1 N m (10.3 0.7 lb ft)
Gently tap the clamp with a soft faced hammer.
Again tighten the clamp. Tighten the clamp to the following torque. ... 14 1 N m (10.3 0.7 lb ft) (2) Wastegate Opening pressure of the wastegate ... 193 kPa (28 psi)
Illustration 5 g01440733
Typical example
(3) Clamp
Illustration 6 g01440735
Typical example of a turbocharger with a wastegate
(3) Clamp
(4) Wastegate (3) Clamp To tighten the clamp (3) on the turbocharger, use the procedure that follows.
Tighten the clamp. Tighten the clamp to the following torque. ... 18 N m (13.3 lb ft)
Loosen the clamp. Loosen the clamp to the following torque. ... 6 N m (53.1 lb in)
Tighten the clamp. Tighten the clamp to the following torque. ... 13.5 1 N m (9.9 0.7 lb ft) (4) Wastegate Opening pressure of the wastegate ... 156 kPa (23 psi)
Illustration 7 g01440737
Typical example
(5) Clamp (5) Clamps To tighten clamps (5) on the turbocharger, use the following procedure:
Tighten the clamp. Tighten the clamp to the following torque. ... 18 3 N m (13.3 2.2 lb ft)
Gently tap the clamp with a soft faced hammer.
Again tighten the clamp. Tighten the clamp to the following torque. ... 18 3 N m (13.3 2.2 lb ft)
Illustration 8 g01440738
Typical example
(6) Clamp
(7) Bolt (6) Clamp To tighten the clamp (6) on the turbocharger, use the following procedure:
Tighten the clamp. Tighten the clamp nut to the following torque. ... 18 N m (13.3 lb ft)
Loosen the clamp. Loosen the clamp nut to the following torque. ... 6 N m (53.1 lb in)
Tighten the clamp. Tighten the clamp nut to the following torque. ... 13.5 1 N m (9.9 0.7 lb ft) (7) Bolt Tighten the bolts (7) for the compressor clamp assembly in opposite pairs. Tighten the bolts for the compressor clamp assembly to the following torque 17.5 1 N m (12.90 0.70 lb ft). Apply 5P-3931 Anti-Seize Compound to the nuts that are used to mount the turbocharger. Tighten the nuts to the following torque 70 15 N m (51.6 11.0 lb ft).
Illustration 9 g01440739
Typical example
(8) Clamp
(9) Bolt (8) Clamp To tighten the clamp (8) on the turbocharger, use the following procedure:
Tighten the clamp. Tighten the clamp to the following torque. ... 18 N m (13.3 lb ft)
Loosen the clamp. Loosen the clamp to the following torque. ... 6 N m (53.1 lb in)
Tighten the clamp. Tighten the clamp to the following torque. ... 13.5 1 N m (9.9 0.7 lb ft) (9) Bolt Tighten the bolt to the following torque. ... 13.5 1 N m (9.9 0.7 lb ft)
Illustration 10