5030721 EVINRUDE GUIDE, Oil level gauge


5030721 GUIDE, Oil level gauge EVINRUDE E70, E70FLTLECS, E70PL4EEC, E70PL4SIA GUIDE
5030721 GUIDE, Oil level gauge EVINRUDE
Rating:
63

Buy GUIDE, Oil level gauge 5030721 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$42.69
 

23-07-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5030721 Tailored Heavy Duty Custom Fit Car Mats Seat Leon Oval Clips (2008-2013) – Black with Grey Trim
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Seat Leon Oval Clips (2008-2013) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 37
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999
E70PL4SIA 2001

Information:


Illustration 1 g01181895
Schematic for the engine temperature sensorsTest Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 2 g01181920
Left side engine view (1) Engine coolant temperature sensor (2) Engine oil temperature sensor (3) Intake manifold air temperature sensor (4) J2/P2 ECM connector
Inspect the connectors for sensors (1), (2), and (3). Also, thoroughly inspect connectors (4). Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01181946
P2 terminals that are associated with the engine temperature sensors (P2-18) Sensor return (P2-32) Engine coolant temperature (P2-34) Engine oil temperature (P2-35) Intake manifold air temperature
Illustration 4 g01155187
Harness connector for the temperature sensors (1) Signal (2) Return
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the temperature sensors.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasions and for pinch points from each sensor to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Turn the keyswitch to the ON position.
Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.Note: Wait at least 15 seconds in order for the diagnostic codes to become active.
Look for a -03 diagnostic code or a -04 diagnostic code.Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active. The problem appears to be resolved.Repair: The problem may have been related to a faulty connection in the harness. Carefully reinspect the connectors and wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.STOP
Not OK - A -04 diagnostic code is active at this time. Proceed to Test Step 3.
Not OK - A -03 diagnostic code is active at this time. Proceed to Test Step 4.Test Step 3. Disconnect the Suspect Sensor in Order to Create an Open Circuit
Turn the keyswitch to the OFF position.
Disconnect the suspect sensor from the engine harness.
Turn the keyswitch to the ON position. Wait at least 15 seconds for activation of the diagnostic codes.
Access the "Active Diagnostic Codes" screen on Cat ET and check for an active -03 diagnostic code for the suspect sensor.
Turn the keyswitch to the OFF position.Expected Result:A -03 diagnostic code is now active for the suspect sensor.Results:
OK - A -04 diagnostic code was active before disconnecting the sensor. A -03 diagnostic code became active after the sensor was disconnected. There may be a problem with the sensor.Repair: Temporarily connect a new sensor to the harness, but do not install the new sensor in the engine. Verify that there are no active diagnostic codes for the new sensor. If there are no active diagnostic codes for the sensor, permanently install the new sensor. Clear any logged diagnostic codes. Verify that the repair eliminates the problem.STOP
Not OK - The -04 diagnostic code is still present. Leave the sensor disconnected. Proceed to Test Step 5.Test Step 4. Create a Short at the Sensor Connector
Disconnect the suspect sensor at the sensor connector.
Fabricate a jumper wire that can be used to create a short between terminal 1 (signal) and terminal 2 (sensor return) at the suspect sensor's connector. Crimp connector pins to each end of the jumper wire.
Install the jumper into the harness side of the sensor connector.
Turn the keyswitch to the ON position.
Access the "Active Diagnostic Code" screen on Cat ET. Check for an active -04 diagnostic code for the suspect sensor.
Turn the keyswitch to the OFF position.Expected Result:A -04 diagnostic code is now active for the suspect sensor.Results:
OK - A -03 diagnostic code was active before creating the short at the sensor connector. A -04 diagnostic code became active after creating the short at the sensor connector.Repair: Temporarily connect a new sensor to the harness, but do not install the new sensor in the engine. Verify that there are no active diagnostic codes for the new sensor. If there are no active diagnostic codes for the sensor, permanently install the new sensor. Clear any logged diagnostic codes.STOP
Not OK - A -03 diagnostic code is still active for the suspect sensors. Proceed to Test Step 5.Test Step 5. Check the Operation of the ECM
Turn the keyswitch to the OFF position.
Check the operation of the ECM by creating an open at the ECM.
Disconnect the P2 ECM connector.
Fabricate a jumper wire that is long enough to reach from a terminal at the ECM connector to t


Parts guide EVINRUDE:

5030607
 
5030607 GUIDE, Valve
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030655
GUIDE, Timing belt
5030655 GUIDE, Timing belt
E70, E70FLTLECS, E70PL4EEC
5030776
 
5030776 GUIDE, Shift rod
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5032691
Back to top