0205971 HANDLE EVINRUDE
10424G, 15404G, 50202C, 50902C, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6802A, 6902M, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S
HANDLE
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- REWIND STARTER » 0205971
50202C, 50203C, 50272C, 50273C 1972
50902C, 50903C, 55974C, 55975C 1979
5802B, 5802E, 5802M, 5803B, 5803E, 5803M 1968
6002B, 6003B 1970
6102E, 6102G, 6103E, 6103G 1971
6202D, 6203D 1972
6302S, 6303S 1973
6402C, 6403C 1974
6802A, 6802C, 6802R, 6803A, 6803C, 6803R 1968
6902M, 6903M 1969
9022A, 9022C, 9023A, 9023C 1970
9122R, 9123R 1971
9222M, 9223M 1972
9322B, 9323B 1973
9822D, 9822E, 9823D, 9823E 1968
9922S, 9923S 1969
Information:
2. Remove two bolts (1) that hold the elbow to the water pump. 3. Remove two bolts (2) that hold elbow (3) to the expansion tank. 4. Remove two bolts (4), clip (5) and water pump (6) from the front timing cover. Remove gaskets.Install Jacket Water Pump (Marine Engine)
1. Inspect water pump elbow gaskets and O-ring seal and make replacements if necessary. 2. Put the water pump (1) and clip in position and install the two bolts that hold them. 3. Install elbow (3) with two bolts to the bottom of the expansion tank.4. Put elbow (2) in position and install two bolts to hold it to the water pump.5. Fill engine with coolant to the correct level.Disassemble Jacket Water Pump (Marine Engine)
start by:a) remove jacket water pump 1. Loosen clamp (1) and remove hose elbow (2) from the pump housing. 2. Remove two bolts (4) and cover (3) from housing. 3. Loosen bolt (5) approximately .25 in. (6.35 mm). Hit the bolt with a soft hammer to remove impeller (6) from the shaft. Remove the bolt (5) and impeller (6). 4. Remove spring (7) and seal assembly (8) from the shaf 5. Turn the housing over and remove bolt (9). 6. After the removal of bolt (9) install bolt from tooling (A) in shaft and gear assembly (10).7. Put plate from driver group in tooling (A) on top of bolt, and install the remainder of tooling (A) on gear and bearing assembly as shown.8. Remove gear and bearing assembly (10) with tooling (A). 9. If necessary, remove bearing (11) from the gear with tool (B). 10. Remove retaining ring (12) from housing with tooling (C). Remove the bearing and shaft assembly. 11. If necessary, remove bearing (13) from shaft with tooling (D) and a press. 12. Turn the housing over and remove seal with tooling (D).Assemble Jacket Water Pump (Marine Engine)
The seal must be installed with the lip toward the bearings. 1. Install the lip type seal in the housing with tooling (A) to the bottom of the seal counterbore. Put a thin layer of engine oil on the lip of the seal. 2. Use a press and tooling (A) to install bearing on shaft (1).3. Install the shaft and bearing assembly in housing. 4. Install retaining ring (2) in housing with tooling (B). 5. Use a press and tooling (A) to install bearing (3) on gear (4).
When gear is installed, make sure the pins on the gear engage the holes in the shaft.
6. Put gear (5) and bearing in position on the shaft and install the washer and bolt.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or permit any foreign material on the wear surface of the carbon or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put the ceramic ring (6) in position in the rubber seal. Use hand pressure and tool (which is with the replacement ring) to install the ceramic ring and rubber seal. 8. Remove the spring from the seal assembly (7). Use hand pressure and the tool (which is with the replacement ring) to install the seal assembly. Push seal assembly (7) on the shaft until the seal face makes light contact. 9. Install spring (8) on the seal assembly. 10. Put impeller (9) in position on the shaft. 11. Install washer and bolt (12). Tighten the bolt to a torque of 28 1 lb.ft. (38 1 N m).12. Install a new gasket (11) and cover (10) on the housing. 13. Put hose and elbow (13) in position on water pump. Install hose clamp (14).end by:a) install jacket water pump
1. Inspect water pump elbow gaskets and O-ring seal and make replacements if necessary. 2. Put the water pump (1) and clip in position and install the two bolts that hold them. 3. Install elbow (3) with two bolts to the bottom of the expansion tank.4. Put elbow (2) in position and install two bolts to hold it to the water pump.5. Fill engine with coolant to the correct level.Disassemble Jacket Water Pump (Marine Engine)
start by:a) remove jacket water pump 1. Loosen clamp (1) and remove hose elbow (2) from the pump housing. 2. Remove two bolts (4) and cover (3) from housing. 3. Loosen bolt (5) approximately .25 in. (6.35 mm). Hit the bolt with a soft hammer to remove impeller (6) from the shaft. Remove the bolt (5) and impeller (6). 4. Remove spring (7) and seal assembly (8) from the shaf 5. Turn the housing over and remove bolt (9). 6. After the removal of bolt (9) install bolt from tooling (A) in shaft and gear assembly (10).7. Put plate from driver group in tooling (A) on top of bolt, and install the remainder of tooling (A) on gear and bearing assembly as shown.8. Remove gear and bearing assembly (10) with tooling (A). 9. If necessary, remove bearing (11) from the gear with tool (B). 10. Remove retaining ring (12) from housing with tooling (C). Remove the bearing and shaft assembly. 11. If necessary, remove bearing (13) from shaft with tooling (D) and a press. 12. Turn the housing over and remove seal with tooling (D).Assemble Jacket Water Pump (Marine Engine)
The seal must be installed with the lip toward the bearings. 1. Install the lip type seal in the housing with tooling (A) to the bottom of the seal counterbore. Put a thin layer of engine oil on the lip of the seal. 2. Use a press and tooling (A) to install bearing on shaft (1).3. Install the shaft and bearing assembly in housing. 4. Install retaining ring (2) in housing with tooling (B). 5. Use a press and tooling (A) to install bearing (3) on gear (4).
When gear is installed, make sure the pins on the gear engage the holes in the shaft.
6. Put gear (5) and bearing in position on the shaft and install the washer and bolt.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or permit any foreign material on the wear surface of the carbon or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put the ceramic ring (6) in position in the rubber seal. Use hand pressure and tool (which is with the replacement ring) to install the ceramic ring and rubber seal. 8. Remove the spring from the seal assembly (7). Use hand pressure and the tool (which is with the replacement ring) to install the seal assembly. Push seal assembly (7) on the shaft until the seal face makes light contact. 9. Install spring (8) on the seal assembly. 10. Put impeller (9) in position on the shaft. 11. Install washer and bolt (12). Tighten the bolt to a torque of 28 1 lb.ft. (38 1 N m).12. Install a new gasket (11) and cover (10) on the housing. 13. Put hose and elbow (13) in position on water pump. Install hose clamp (14).end by:a) install jacket water pump
Parts handle EVINRUDE:
0312858
0312858 HANDLE, Steering, inner half
115983E, 18002C, 18102S, 18202R, 18802A, 18902B, 25002C, 25102S, 25202R, 25902B, 6002B, 6102E, 6202D, 6802A, 6902M
0312859
0203122
0312184
0312184 HANDLE,Latch
5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S
0378615
0309732
0315939
0318948
0318948 HANDLE LATCH
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, E10ECSE, E10ELCID, E10ELCNS, E15ECIS, E15ECNC, E15ECSD