0206843 EVINRUDE HANDLE, Starter

Table 1
Diagnostic Codes Table
CDL Code Code Description Comments
100-3 Engine Oil Pressure Sensor : Voltage Above Normal The Electronic Control Module (ECM) detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
100-4 Engine Oil Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
101-3 Crankcase Air Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
101-4 Crankcase Air Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
274-3 Atmospheric Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
274-4 Atmospheric Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
460-3 Fuel Pressure Sensor - After Fuel Filter : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
460-4 Fuel Pressure Sensor - After Fuel Filter : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
460-21 Fuel Pressure Sensor - After Fuel Filter : Data Drifted Low The code is logged.
The sensor is set to the default value.
827-3 Left Exhaust Temperature Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
827-4 Left Exhaust Temperature Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
828-3 Right Exhaust Temperature Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
828-4 Right Exhaust Temperature Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
1785-3 Intake Manifold Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
1785-4 Intake Manifold Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
1785-21 Intake Manifold Pressure Sensor : Data Drifted Low The code is logged.
The sensor is set to the default value.
2350-3 Left Exhaust #2 Temperature : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
2350-4 Left Exhaust #2 Temperature : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
2351-3 Right Exhaust #2 Temperature : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
2351-4 Right Exhaust #2 Temperature : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
2738-3 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
2738-4 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
3031–3 Intake Manifold #2 Pressure Sensor: Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
3031–4 Intake Manifold #2 Pressure Sensor: Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
3385-3 EGR Intake Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
3385-4 EGR Intake Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
3385-21 EGR Intake Pressure Sensor : Data Drifted Low The code is logged.
The sensor is set to the default value.
3387-3 Engine Exhaust Gas Recirculation Differential Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value.
3387-4 Engine Exhaust Gas Recirculation Differential Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a default value. The supply voltage is routed to terminal 1 of each sensor connector. The sensor return is routed to terminal 2 of each sensor connector. For the pressure sensors, the sensor signal is routed to terminal 3 of each sensor connector. The sensor signal for the exhaust temperature sensors is routed to terminals 3 and 4