0279891 EVINRUDE HANDLE & SHAFT,Rear


0279891 HANDLE & SHAFT,Rear EVINRUDE 55642E HANDLE
0279891 HANDLE & SHAFT,Rear EVINRUDE
Rating:
83

Buy HANDLE & SHAFT,Rear 0279891 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

Compatible models:

55642E   EVINRUDE

BRP EVINRUDE entire parts catalog list:

55642E, 55643E, 55672E, 55673E 1976

Information:

Probable Causes
Switches
Batteries
Electric starting system (if equipped)
Flywheel ring gear
Driven equipment
Hydraulic cylinder lock
Worn engine componentsRecommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Inspect the Switches
A. Check the keyswitch input to the ECM.
B. Check engine shutdown switches.
C. Connect Cat® Electronic Technician (ET) to the service tool connector.
D. Use Cat ET to verify the status of the shutdown switches.
Switches
Result: The switch statuses are good.
Proceed to Test Step 2.
Result: There is a problem with a switch.
Repair: Repair or replace damaged switch.
If the problem is not resolved, proceed to Test Step 2.
2. Inspect the Batteries
A. Charge the batteries, if necessary. Refer to Testing and Adjusting , Battery - Test for additional information.
Batteries
Result: The batteries are in good condition.
Proceed to Test Step 3.
Result: There is a problem with the batteries.
Repair: Repair or replace the batteries.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Electric Starting System
A. If the application is equipped with an electric starting system, perform the following procedure:
a. Check the wiring to the starting motor solenoid. Refer to the electrical schematic.
b. Check the engine start switch and the engine start relay for electrical power.
c. Check the starting motor cables. If the starting motor cables are corroded, remove the starting motor cables and clean the starting motor cables.
d. Test the operation of the starting motors.
Starter
Result: The electric starter is in good condition
Proceed to Test Step 6.
Result: There is a problem with the electric starter.
Repair: Repair or replace damaged electric starter.
If the problem is not resolved, proceed to Test Step 6.
4. Inspect the Flywheel Ring Gear for Damage
Ring Gear
Result: There is no apparent damage to the flywheel ring gear.
Proceed to Test Step 5.
Result: There is a problem with the flywheel ring gear.
Repair: Repair or replace the ring gear.
If the problem is not resolved, proceed to Test Step 5.
5. Inspect the Driven Equipment
Driven Equipment
Result: The driven equipment is in good condition.
Proceed to Test Step 6.
Result: There is a problem with the driven equipment.
Repair: Repair or replace damaged driven equipment.
If the problem is not resolved, proceed to Test Step 6.
6. Check for Hydraulic Cylinder Lock
A. If an injector has been replaced, evacuate any fluids from the cylinder and attempt to start the engine. Fuel will flow from the cylinder head into the cylinders when a unit injector is removed.
B. If the engine will not start, check for fluid in the cylinders (hydraulic cylinder lock) by removing the individual unit injectors. Check for damaged seals. Determine the type of fluid that locked up the cylinder.
C. If there was a coolant leak, determine the cause of the leak.
D. If there was excessive fuel in the cylinder, replace the seals and reinstall the injector. Drain any excess fuel from the cylinder head.
Hydraulic Cylinder Lock
Result: The engine does not have a hydraulic cylinder lock.
Proceed to Test Step 7.
Result: The engine has a hydraulic cylinder lock.
Repair: Perform the necessary repairs.
If the problem is not resolved, proceed to Test Step 7.
7. Inspect the Engine for Internal Problems
A. If a mechanical problem is suspected, disassemble the engine. Refer to the Disassembly and Assembly manual for additional information.
B. Inspect the internal components for the following conditions:
- Seizure
- Broken components
- Bent components
Damaged or Worn Engine Components
Result: There are worn or damaged engine components.
Repair: Repair or replace the worn or damaged engine components.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts handle EVINRUDE:

0279222
 
0279222 HANDLE & SHAFT
50172S, 50202C, 50302R, 50442M, 50542B, 55642E
0320977
0279890
Back to top