0312184 EVINRUDE HANDLE,Latch


0312184 HANDLE,Latch EVINRUDE 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S HANDLE
0312184 HANDLE,Latch EVINRUDE
Rating:
38

Buy HANDLE,Latch 0312184 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

BRP EVINRUDE entire parts catalog list:

5802B, 5802E, 5802M, 5803B, 5803E, 5803M 1968
6002B, 6003B 1970
6102E, 6102G, 6103E, 6103G 1971
6202D, 6203D 1972
6302S, 6303S 1973
6402C, 6403C 1974
6504R, 6505R 1975
6604A, 6605A 1976
6704M, 6705M 1977
6802A, 6802C, 6802R, 6803A, 6803C, 6803R 1968
6804B, 6805B 1978
6902M, 6903M 1969
6904E, 6905E 1979
9022A, 9022C, 9023A, 9023C 1970
9122R, 9123R 1971
9222M, 9223M 1972
9322B, 9323B 1973
9822D, 9822E, 9823D, 9823E 1968
9922S, 9923S 1969

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     268-1968     Pry Bar     1    Start By:
Remove the valve mechanism cover.
Remove the fuel injection line.
Illustration 1 g01264292
Illustration 2 g01264293
Note: Do not remove the quill tube. This action will reduce the risk of contamination to the system.
Fully loosen quill tube nut (1). Pull quill tube (1) out of the bore until you see O-ring seal (2). This action will ensure that the injector does not contact the quill tube during removal. At this time, inspect O-ring seal (2) for wear or for damage. Replace the O-ring seal if necessary.
Illustration 3 g02161166
Typical Example
Disconnect harness assembly (3) from the unit injector.
Illustration 4 g02161316
Typical Example
Remove bolt (5) from clamp (6) .Note: When possible, remove the unit injector by hand by twisting the unit injector and pulling upward. Be sure not to strike the unit injector during the removal procedure.
If unit injector (4) cannot be removed by hand, go to Step 5.
Illustration 5 g02161361
Typical ExampleNote: Do not damage the unit injector during removal. Side loading may damage to the unit injector.
Position Tooling (A) under unit injector clamp (6). Carefully remove unit injector (4) from the cylinder head.Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
B     -     Scotch Brite     1    
C     1U-5718     Vacuum Pump     1    
169-7372 Bottle Assembly     1    
4C-4057 Clear Plastic Tubing
7.92 mm (0.312 inch) OD     1    
4C-4055 Clear Plastic Tubing
6.35 mm (0.250 inch) OD        
D     9U-5470     Reamer     1    
E     4C-6161     Tube Brush     1    
F     9U-6862     Tapered Brush     1    
G     4C-6774     Vacuum Gun Kit     1    
H     4C-5027     Tap Wrench     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Evacuate as much fuel and oil as possible from the cylinder head before installing the unit injector. Several evacuations may be necessary. Use Tooling (C) to remove the fuel and oil from the cylinder.Note: Tooling (F) is available to clean loose material from the sleeve bore and the cylinder.
Clean the carbon from the sleeve, the sleeve bore, and the end of the unit injector. Clean the carbon from the seat area that is inside of the cylinder head. A fine grade of Tooling (B) is preferred. Clean the carbon from the cylinder head. If the sleeve of the unit injector has been removed, use Tooling (D) to remove only carbon from the surface of the sleeve. If the sleeve of the unit injector is installed, use Tooling (E) to clean the carbon deposit from the inside of the sleeve.The following procedure is the preferred method of cleaning the sleeve bore.Place a 38 mm (1.5 inch) square piece of Scotch Brite material on the end of Tooling (F). Twist Tooling (F) with Tooling (H) against the lower surface of the sleeve bore.The surface should be cleaned until the surface is smooth and shiny. The entire sleeve bore should be cleaned in order to remove any loose carbon particles.Note: Tooling (G) is available to clean loose material from the sleeve bore and the cylinder.


Parts handle EVINRUDE:

0312858
 
0312858 HANDLE, Steering, inner half
115983E, 18002C, 18102S, 18202R, 18802A, 18902B, 25002C, 25102S, 25202R, 25902B, 6002B, 6102E, 6202D, 6802A, 6902M
0312859
 
0312859 HANDLE, Steering, outer half
18002C, 18802A, 18902B, 25002C, 25902B, 6002B, 6802A, 6902M
0205971
 
0205971 HANDLE
10424G, 15404G, 50202C, 50902C, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6802A, 6902M, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S
0378615
 
0378615 HANDLE,Gearshift
6002B, 6102E, 6202D, 6802A, 6902M
0309732
 
0309732 HANDLE,Carrying
9022A, 9122R, 9222M, 9322B, 9822D, 9922S
0315939
 
0315939 HANDLE, Steering, outer half
18102S, 18202R, 25102S, 25202R, 6102E, 6202D
0318213
HANDLE, Steering, inner half
0318213 HANDLE, Steering, inner half
18304A, 25302A, 25402M, 25502B, 25602E, 25702H, 35602G, 6302S, 6402C, 6504R, 6604A, 6704M, 6804B, 6904E
Back to top