0396565 HANDLE, Steering EVINRUDE
E10ECDB, E15ECDE, E20CRCDC, E25ECDR, E25RWCDC, E25RWCUR, E30ECDM, E35RCDM
HANDLE
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$788.08
14-02-2022
-: -
K&M 039-6565 Ford-New Holland 7410-TW Series Mechanical Suspension for Original Seat
Grimmer MSG85 Air Suspension || Seat Adapter Plates || Slide Rails || Install Hardware
Grimmer MSG85 Air Suspension || Seat Adapter Plates || Slide Rails || Install Hardware
Number on catalog scheme: 8
BRP EVINRUDE entire parts catalog list:
- STEERING HANDLE & THROTTLE CONTROL » 0396565
E20CRCDC, E20CRLCDC, E20ECDC, E20ELCDC, E20TECDC 1986
E25ECDR, E25ELCDR, E25RCDC, E25RLCDC, E25TECDC, E25TELCDC 1986
E25RWCDC, E25RWLCDC 1986
E25RWCUR, E25RWLCUR 1987
E30ECDM, E30ELCDM, E30RCDM, E30RLCDM, E30TECDM, E30TELCDM 1986
E35RCDM, E35RLCDM 1986
Information:
Table 1
Diagnostic Trouble Code for the Water-in-Fuel Sensor
J1939 Code CDL code Code Description
(code descriptions may vary Comments
97-3 3547-3 Water In Fuel Indicator : Voltage Above Normal The ECM detects the following conditions:
An open circuit in the Water-In-Fuel (WIF) sensor circuit.
The ECM has been powered for less than 5 seconds.
The warning lamp will stay on when the "indicator lamp self check" has been completed. The ECM will disable the function to detect water in fuel while the code is active. Water-in-Fuel Sensor OperationThe WIF sensor is a normally open sensor. During normal operation, there will be no signal sent from the WIF sensor to the ECM. If water is detected in the fuel, the sensor will send a signal to the ECM. If the signal remains constant for 45 seconds, a 97-15 (E232-1) diagnostic code will become active. If the signal remains constant for 1 hour, a 97-16 (E232-2) diagnostic code will become active. These diagnostic codes can also be caused by a short in the WIF sensor circuit.During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Thoroughly inspect the connector for the WIF sensor and the P1/J1 ECM connector. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the WIF sensor.
D. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
E. Check the harness for abrasions, for pinch points, and for corrosion.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors
Parts handle EVINRUDE:
0327164
0327164 HANDLE, Remote control
C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100STLCCA, E100STLCEM, E100STLESB, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLESM, E100WTLZ, E10EESC, E110MLCCA, E110MLCDC, E110MLCEM, E110MLCUR, E115MLCNB, E115MLCOS, E115MLCRD,
0329969
0329969 HANDLE, Starter
E20CRCCA, E20CRCDC, E20CRCOS, E20CRCUR, E25ECCM, E25ECDR, E25ECOC, E25ECRS, E25ECUA, E25RWCDC, E25RWCOS, E25RWCRD, E25RWCUR, E30ECCE, E30ECDM, E30ECOA, E30ECRR, E30ECUB, E35ECRR, E35RCCE, E35RCDM, E35RCUB, U25RWA
0331361
0331361 HANDLE, Starter
BE3REDS, BE4BREDS, BE4BREUC, BE4RDHEDS, E10ECCD, E10ECDB, E10ECES, E10ECUE, E10EEIR, E10EENA, E10EESC, E15ECCS, E15ECDE, E15ECEC, E15ECUD, E15EEIA, E15EENM, E15EESR, E3RCCM, E3RCUA, E3REOD, E3REUC, E4BRECRJ, E4RCCS, E4RCEC, E4RCUD, E4RDHCCS, E4RDHCDE
0395910
0395910 HANDLE LATCH
B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE30EECS, BE30EEDE, BE30EEUD, E10ECCD, E10ECDB, E10ECES,