0397702 EVINRUDE HANDLE, Gearshift


0397702 HANDLE, Gearshift EVINRUDE BE4RDHEDS, E4RDHCCS, E4RDHCEC, E4RDHEIA, E4RDHENM, E4RDHEOD, E4RDHERE, E4RDHESR, E4RDHETB, E6RCCS, E6RCEC, E6RESR, E8RCCS, E8RCEC, E8RESR HANDLE
0397702 HANDLE, Gearshift EVINRUDE
Rating:
103

Buy HANDLE, Gearshift 0397702 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

BRP EVINRUDE entire parts catalog list:

BE4RDHEDS, BE4RDHLEDS 1996
E4RDHCCS, E4RDHLCCS 1988
E4RDHCEC, E4RDHLCEC 1989
E4RDHEIA, E4RDHLEIA 1991
E4RDHENM, E4RDHLENM 1992
E4RDHEOD, E4RDHLEOD 1995
E4RDHERE, E4RDHLERE 1994
E4RDHESR, E4RDHLESR 1990
E4RDHETB, E4RDHLETB 1993
E6RCCS, E6RLCCS, E6SLCCS 1988
E6RCEC, E6RLCEC, E6SLCEC 1989
E6RESR, E6RLESR, E6SLESR 1990
E8RCCS, E8RLCCS, E8SRLCCS 1988
E8RCEC, E8RLCEC, E8SRLCEC, TE8RCEC, TE8RLCEC 1989
E8RESR, E8RLESR, E8SRLESR, TE8RLESCF 1990

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
611-5
System Diagnostic Code #1 : Current Below Normal N/A This code indicates that there is a problem with the engine starter motor relay and/or the electrical circuit on the Electronic Control Module (ECM).
611-6
System Diagnostic Code #1 : Current Above Normal N/A This code indicates that there is a problem with the engine starter motor relay and/or the electrical circuit on the ECM.
677-5
Engine Starter Motor Relay : Current Below Normal 444-5
Starter Motor Relay : Current Below Normal This code indicates that there is a problem with the engine starter motor relay and/or the electrical circuit on the ECM.
677-6
Engine Starter Motor Relay : Current Above Normal 444-6
Starter Motor Relay : Current Above Normal This code indicates that there is a problem with the engine starter motor relay and/or the electrical circuit on the ECM.
4210-5
Engine Pre-lube Drive : Current Below Normal 338-5
Engine Pre-Lube Pump Relay : Current Below Normal This code indicates that there is a problem with the prelubrication solenoid and/or the electrical circuit on the ECM.
4210-6
Engine Pre-lube Drive : Current Above Normal 338-6
Engine Pre-Lube Pump Relay : Current Above Normal This code indicates that there is a problem with the prelubrication solenoid and/or the electrical circuit on the ECM. Electrical Checkouts on the Cat® Electronic Technician (ET)
Table 2
Component Electrical Checkout
Engine Pre-lube Drive Engine Pre-lube Override
Engine Starter Solenoid Attempt to start the engine. Once the ECM attempts to energize the solenoid, the code will become active. Refer to the application-specific schematic for the "Engine Starter Motor Solenoid" wiring circuit.
Illustration 1 g03882053
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -5 code is active or logged.
Proceed to Test Step 2.
Result: A -6 code is active or logged.
Proceed to Test Step 3.
2. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, free of corrosion, and securely connected.
B. Disconnect the solenoid from the harness.
C. Connect a jumper wire between the terminals of the harness connector for the affected coil. The coil is replaced with a short circuit.
Create a Short
Result: A -5 code became active during the electrical checkout. The ECM did not detect the jumper wire. There is an open circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -6 code is activated during the electrical checkout. The ECM detected the jumper wire. There is a problem with the solenoid.
Repair: Replace the solenoid.
Verify that the repair eliminated the problem.
3. Check the Wiring for a Short Circuit
A. Disconnect the solenoid from the harness.
Create an Open
Result: A -6 code became active during the electrical checkout. The ECM did not detect the open circuit. There is a short circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -5 code is activated during the electrical checkout. The ECM detected the open circuit. There is a problem with the solenoid.
Repair: Replace the solenoid.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts handle EVINRUDE:

0312833
 
0312833 HANDLE,Latch
3802A, 4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4706B, 4806E, 4902B, BE4RDHEDS, E4RDHCCS, E4RDHCDE, E4RDHCEC, E4RDHCUD, E4RDHEIA, E4RDHENM, E4RDHEOD, E4RDHERE, E4RDHESR, E4RDHETB, E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCCS, E6RCDE, E6RCEC, E6RC
0331361
HANDLE, Starter
0331361 HANDLE, Starter
BE3REDS, BE4BREDS, BE4BREUC, BE4RDHEDS, E10ECCD, E10ECDB, E10ECES, E10ECUE, E10EEIR, E10EENA, E10EESC, E15ECCS, E15ECDE, E15ECEC, E15ECUD, E15EEIA, E15EENM, E15EESR, E3RCCM, E3RCUA, E3REOD, E3REUC, E4BRECRJ, E4RCCS, E4RCEC, E4RCUD, E4RDHCCS, E4RDHCDE
0398736
 
0398736 HANDLE, Steering
E4RDHCCS, E4RDHCEC, E4RDHCUD, E4RDHESR, E6RCCS, E6RCEC, E6RCUD, E6RESR, E8RCCS, E8RCEC, E8RCUD, E8RESR, VE14RCCS, VE14RCEC
0434124
 
0434124 HANDLE, Steering
BE4RDHEDS, E4RDHEIA, E4RDHENM, E4RDHEOD, E4RDHERE, E4RDHETB
Back to top