0335433 EVINRUDE HOOK, Front


0335433 HOOK, Front EVINRUDE BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E5DRECR, E6REIA, E6RENM, E6REOD, E6RERE, E6RETB, E8DREEA, E8DRSSM, E8RECR, E8REIA, E8RENM, E8REOD, E8RERE, E8RETB, E8REUC, E8WREES, E8WRLSIR, E8WRLSSC HOOK
0335433 HOOK, Front EVINRUDE
Rating:
58

Buy HOOK, Front 0335433 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

BRP EVINRUDE entire parts catalog list:

BE5DREDS, BE5DRLEDS 1996
BE5DREUC, BE5DRLEUC 1997
BE6DRECR, BE6DRLECR, E6RECR, E6RLECR 1998
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8RCB, BE8RCLB 1997
BE8RCH, BE8RCLH 1996
BE8RCLT, BE8RCT 1998
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E5DRECR, E5DRLECR 1998
E6REIA, E6RLEIA, E6SLEIA 1991
E6RENM, E6RLENM, E6SLENM 1992
E6REOD, E6RLEOD, E6SLEOD 1995
E6RERE, E6RLERE, E6SLERE 1994
E6RETB, E6RLETB, E6SLETB 1993
E8DREEA 1999
E8DRSSM 2000
E8RECR, E8RLECR, E8SRLECA 1998
E8REIA, E8RLEIA, E8SRLEIA 1991
E8RENM, E8RLENM, E8SRLENM 1992
E8REOD, E8RLEOD, E8SRLEOD 1995
E8RERE, E8RLERE, E8SRLERE 1994
E8RETB, E8RLETB, E8SRLETB 1993
E8REUC, E8RLEUC, E8SRLEUC 1997
E8WREES, E8WRLEES 1999
E8WRLSIR, E8WRSIR 2001
E8WRLSSC, E8WRSSC 2000

Information:

1. Remove coolant from the radiator and cylinder block.2. Remove fuel injection lines (5). Put a cap on all openings.3. Remove breather tube (6).4. Remove supply line (2) and drain line (4) for turbocharger.5. Remove air cleaner housing (1) and air inlet pipe.6. Remove nuts (3) from exhaust manifold.7. Remove turbocharger and exhaust manifold as a unit. Weight is 85 lb. (39 kg). 8. Remove water line (10) between air compressor and cylinder head.9. Remove air inlet line (11) for air compressor.10. Disconnect line (9) for water temperature.11. Remove water elbow (8), regulator, and hose.12. Remove bolts (7) that hold water elbow to the cylinder head.13. Remove valve cover from the engine. 14. Remove the rocker shaft (12) and push rods.15. Loosen the fan belts.16. Remove bolts from the fan drive. Install tool (A) to hold the fan drive in place.17. Remove the bolts and washers from the cylinder head.18. Fasten a hoist and remove the cylinder head. Weight is 210 lb. (95 kg).Install Cylinder Head
1. Install a new, dry cylinder head gasket. 2. Fasten a hoist and put cylinder head (1) in position on cylinder block. 3. Install push rods (3) and rocker shaft (2). The dowel pin (4) on each end of the rocker shaft must be in alignment with the hole (5) in the head. If the pins and holes are not in alignment when bolts are tightened, damage to the rocker shaft and arms can be the result.4. Put 5P3931 Anti-Seize Compound on the threads of cylinder head and rocker shaft bolts. Install the bolts and washers and tighten bolts in the following step sequence: Step 1. Tighten all bolts in number sequence to a torque of 115 lb.ft. (155 N m).Step 2. Tighten all bolts in number sequence to a torque of 185 13 lb.ft. (250 17 N m) again.Step 3. Tighten all bolts in number sequence (hand turn only) to a torque of 185 13 lb.ft. (250 17 N m) again.Step 4. Tighten all bolts in letter sequence to a torque of 22 lb.ft. (28 N m).Step 5. Tighten all bolts in letter sequence to a torque of 32 5 lb.ft. (43 7 N m).Step 6. Tighten all bolts (hand turn only) in letter sequence to a torque of 32 5 lb.ft. (43 7 N m).5. Make adjustments to the valves. The intake valve clearance is .015 in. (0.38 mm) and the exhaust valve clearance is .025 in. (0.64 mm).6. Connect fan drive to the cylinder head and remove tool (A).7. Tighten fan belts. See INSTALL ALTERNATOR for the correct belt tension adjustment.8. Install valve cover. Tighten bolts by number in sequence shown to 96 24 lb.in. (10.9 2.8 N m). 9. Install air cleaner housing (6) and bracket. 10. Install bolts (7) that hold water elbow to cylinder head.11. Install hose, regulator and water elbow.12. Install air inlet line (9) for air compressor.13. Install water line (8) between air compressor and cylinder head.14. Connect line (10) for water temperature.15. Install turbocharger and exhaust manifold. 16. Install supply line (11) and drain line (13) for turbocharger.17. Remove caps from fuel injection lines and install fuel injection lines (12). Tighten nuts on lines to a torque of 30 5 lb.ft. (40 7 N m).18. Fill cooling system to the correct level.end by:a) install hood


Parts hook EVINRUDE:

0434168
 
0434168 HOOK REPAIR KIT, Rear
BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E5DRECR, E6REIA, E6RENM, E6REOD, E6RERE, E6RETB, E8DREEA, E8DRSSM, E8RECR, E8REIA, E8RENM, E8REOD, E8RERE, E8RETB, E8REUC, E8WREES, E8WRLSIR, E8WRLSSC
Back to top