5041724 HOSE EVINRUDE
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
HOSE
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- INTAKE MANIFOLD & FUEL PUMP » 5041724
B10EL4INS 2012
B10PL4AAA, B10PX4AAA, E10PL4AAA, E10PX4AAA 2012
B10PL4AAB, B10PX4AAB, E10PL4AAB, E10PX4AAB 2012
B10PL4INS 2012
B10PX4INS, E10PX4INS 2012
B10R4AAA, B10RL4AAA, E10R4AAA, E10RL4AAA 2012
B10R4AAB, B10RL4AAB, B10TEL4AAB, E10R4AAB, E10RL4AAB 2012
B10R4INS, E10R4INS 2012
B10RL4INS, E10RL4INS 2012
B10TEL4AAA, E10TEL4AAA 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4AAA, B10TPX4AAA, E10TPL4AAA, E10TPX4AAA 2012
B10TPL4AAB, B10TPX4AAB, E10TPL4AAB, E10TPX4AAB 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012
E10EL4AAB 2012
E10EL4INS 2012
E10PL4INS 2012
E10TEL4AAB 2012
Information:
1. Remove fuel lines (1) from the engine. 2. Disconnect tube assembly (3) and wires (2) from the governor. 3. Remove the bolts, the clamps and service meter (4) from the accessory drive housing. 4. Remove bolts (5) that hold the fuel injection pump housing to the accessory drive housing. 5. Fasten strap (7) and a hoist to fuel injection pump housing and governor (6).6. Remove bolts (8) and fuel injection pump housing and governor (6) from the engine. The weight of the fuel injection pump housing and governor is 39 kg (87 lb.). 7. If necessary remove seals (9) from the fuel injection pump housing.Install Fuel Injection Pump Housing And Governor
1. Use tool (A) and put engine at top center compression stroke. See TESTING AND ADJUSTING. 2. Remove nuts (1) and cover (2) from the automatic timing advance. 3. Loosen four bolts (2) that hold the automatic timing advance to the drive shaft for the fuel injection pump. 4. Remove plug (3) from the fuel injection pump housing. 5. Time the fuel injection pump by turning the camshaft until the notch in the camshaft is in alignment with the hole in the fuel injection pump housing. Install tool (B) through the housing and into the notch of the camshaft. 6. Inspect for wear or damage and make a replacement if necessary of seals (4).7. Put seals (4) in position on the fuel pump housing. 8. Fasten strap (6) and a hoist to fuel injection pump housing and governor (5).9. Install gasket (7) and fuel injection pump housing and governor (5) on the accessory drive housing and engine block with the bolts that hold it. 10. Tighten bolts (8) of automatic timing advance (9) in the following sequence.a) Tighten bolts (8) evenly to a torque of 35 N m (25 lb.ft.).b) Tighten bolts (8) evenly to a torque of 70 N m (50 lb.ft.).c) Tighten bolts (8) evenly to a final torque of 135 7 N m (100 5 lb.ft.). 11. To check for correct engine timing follow the steps below.a) Remove tool (B) from the fuel pump housing and the bolt from the flywheel.b) Turn the flywheel counterclockwise (as seen from the front of the engine) two complete revolutions.c) If the engine is in correct timing, tool (B) can be installed in the notch of the camshaft in the fuel injection pump housing and the bolt can be installed in the flywheel.d) If tool (B) and the bolt can not be correctly installed, the timing is not correct and Step 11 must be repeated. The flywheel can be out of alignment 1° and still be in correct timing. 12. Remove tool (B) and install plug (10) in the fuel injection pump housing.13. Install service meter (11) on the accessory drive housing with the clamps and bolts. 14. Install gasket (13) and cover (12) to the front cover. 15. Connect tube assembly (14) and wires (15) to the governor. 16. Install fuel lines (16) to the block and fuel injection pump housing.END BY:a) install fuel lines
1. Use tool (A) and put engine at top center compression stroke. See TESTING AND ADJUSTING. 2. Remove nuts (1) and cover (2) from the automatic timing advance. 3. Loosen four bolts (2) that hold the automatic timing advance to the drive shaft for the fuel injection pump. 4. Remove plug (3) from the fuel injection pump housing. 5. Time the fuel injection pump by turning the camshaft until the notch in the camshaft is in alignment with the hole in the fuel injection pump housing. Install tool (B) through the housing and into the notch of the camshaft. 6. Inspect for wear or damage and make a replacement if necessary of seals (4).7. Put seals (4) in position on the fuel pump housing. 8. Fasten strap (6) and a hoist to fuel injection pump housing and governor (5).9. Install gasket (7) and fuel injection pump housing and governor (5) on the accessory drive housing and engine block with the bolts that hold it. 10. Tighten bolts (8) of automatic timing advance (9) in the following sequence.a) Tighten bolts (8) evenly to a torque of 35 N m (25 lb.ft.).b) Tighten bolts (8) evenly to a torque of 70 N m (50 lb.ft.).c) Tighten bolts (8) evenly to a final torque of 135 7 N m (100 5 lb.ft.). 11. To check for correct engine timing follow the steps below.a) Remove tool (B) from the fuel pump housing and the bolt from the flywheel.b) Turn the flywheel counterclockwise (as seen from the front of the engine) two complete revolutions.c) If the engine is in correct timing, tool (B) can be installed in the notch of the camshaft in the fuel injection pump housing and the bolt can be installed in the flywheel.d) If tool (B) and the bolt can not be correctly installed, the timing is not correct and Step 11 must be repeated. The flywheel can be out of alignment 1° and still be in correct timing. 12. Remove tool (B) and install plug (10) in the fuel injection pump housing.13. Install service meter (11) on the accessory drive housing with the clamps and bolts. 14. Install gasket (13) and cover (12) to the front cover. 15. Connect tube assembly (14) and wires (15) to the governor. 16. Install fuel lines (16) to the block and fuel injection pump housing.END BY:a) install fuel lines
Parts hose EVINRUDE:
0772564
0772564 HOSE, Fuel connectors
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5041726
5041726 HOSE
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5041719
5041719 HOSE Evaporative emissions related part
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN