0353088 EVINRUDE *INSULATION, Sound - port/center

2. Remove tube assembly (1) and brace (2). 3. Remove plate assembly (3) from the oil filter housing. 4. Remove bolt (4) that holds clamp (7) in place.5. Remove bolts (5) and flange that hold tube assembly (6) in the oil cover. 6. Remove the top outside bolts that hold the oil filter housing in place. Install two 1/2"-13 NC guide pins (8). Remove nuts (9). 7. Fasten a hoist as shown to the oil filter housing. Remove bolts (10) and (12) that hold the oil filter housing in place. Remove oil filter housing (11). The weight is 135 lb. (61 kg). The seal between the oil filter housing and is free to fall when the oil filter housing is removed.Install Oil Filter Housing
1. Fasten a hoist to the oil filter housing. Make sure the seal is in position between the oil filter housing and the support. Put oil filter housing (1) in position on the guide pins. Make sure tube assembly (2) slides into the oil cooler. 2. Install bolts (3) and (4) that hold the oil filter housing in place. 3. Install nuts (6). Remove guide pins (5) and install the bolts for the oil filter housing. 4. Put the clamp in place and install bolt (7) that holds it. Install flanges (8) and bolts (9) that hold the tube assembly in the oil cooler. 5. Install plate assembly (10) on the oil filter housing. Tighten the bolts to a torque of 150 20 lb.ft. (205 27 N m). 6. Put the gasket in place and install tube assembly (11). Install brace (12).7. Fill the radiator with coolant to the correct level. See LUBRICATION AND MAINTENANCE GUIDE.end by:a) install fuel filterb) install fan and fan driveDisassemble Oil Filter Housing
start by:a) remove oil filter housing 1. Remove seal (1) from the oil filter housing. 2. Remove plate (2) that holds tube assembly (3) in the oil filter housing. Remove tube assembly (3).3. Remove cover (4) from the oil filter housing.
Pins (6) hold springs (9) under compression.
4. Use a punch and hammer and remove pins (6), cups (7), seal (8) and springs (9) from guides (5). 5. Remove bolts (10) and washers that hold guides (5) in cover (4). Remove plug (11) and gasket from cover (4). 6. Remove cover (12) from the other end of the oil filter housing. Remove plug (13) and gasket from the cover. 7. Remove four filter elements (14) from the oil filter housing. 8. Use tool (A) and remove retaining ring (15) that holds the valve in place. 9. Use a brass punch and push the valve from the other side of the housing with a hammer and remove valve (16).
Retaining ring (17) holds a spring under compression.
10. Use tool (A) and remove retaining ring (17) from the valve. Remove slug (18), the spring and guide from the valve (16). 11. Remove indicator assembly (19) from the oil filter housing.12. Remove valve assembly (20) from the oil filter housing. Assemble Oil Filter Housing
1. Make sure all the parts of the oil filter are clean. Put clean oil on the parts of the oil filter. Inspect all parts for damage and make replacements if needed. 2. Install valve assembly (1) in the oil filter housing. 3. Install indicator assembly (2) in the oil filter housing. 4. Install guide (4), spring (5) and slug (6) in valve (3). Use tool (A) and install retaining ring (7) in valve (3). 5. Use tool (B) and install valve (3) in the oil filter housing. Install the valve to a depth of 4.63 in. (11.8 cm) from the outside surface of the oil filter housing. 6. Use tool (A) and install retaining ring (8) in the oil filter housing. 7. Install four oil filter elements (9) in the oil filter housing. 8. Install tube assembly (10) in the oil filter housing. 9. Install gasket and plug (11) in cover (13). Tighten the plug to a torque of 30 5 lb.ft. (40 7 N m).10. Put the guides in position on the other side of cover (13) and install washers and bolts (12) that hold the guides in place. 11. Install springs (17), seals (16) and cups (15) on the guides. Install pins (14) in the guides. 12. Install the gasket and cover (13) on the oil filter housing. 13. Install gasket and plug (18) in cover (19). Tighten the plug to a torque of 20 5 lb.ft. (25 7 N m).14. Install the gasket and cover (19) on the oil filter housing. 15. Install seal (20) on the oil filter housing. Put clean grease on the seal to hold it in place.end by:a) install oil filter housing