0279340 EVINRUDE LEAD, Horn to switch


0279340 LEAD, Horn to switch EVINRUDE 100193A, 100293R, 125183C, 125283R, 50172S, 50202C, 60172C, 65272S, 85193A, 85293R LEAD
0279340 LEAD, Horn to switch EVINRUDE
Rating:
98

Buy LEAD, Horn to switch 0279340 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 33
 

BRP EVINRUDE entire parts catalog list:

100193A, 100193C 1971
100293R 1972
125183C 1971
125283R 1972
50172S, 50173S 1971
50202C, 50203C, 50272C, 50273C 1972
60172C, 60172E, 60173C, 60173E 1971
65272S, 65273S 1972
85193A, 85193H 1971
85293R 1972

Information:

1. Loosen the bleed valves and release the air pressure in the air tanks.2. Drain the oil from the oil pan. 3. Remove two short bolts (1) and two longer bolts (3) from manifold (2) and the BrakeSaver housing. Remove manifold (2). Remove the O-ring seals from the manifold. 4. Remove oil temperature sensing unit (4) from the BrakeSaver control valve.5. Disconnect air line (5) and hose assembly (6) from the BrakeSaver control valve. 6. Remove bolt (7) and retainer (8) that hold the oil lines in the BrakeSaver control valve. 7. Disconnect oil lines (9) and (10) from the oil cooler. Remove oil lines (9) and (10) from the BrakeSaver control valve. 8. Remove bolts (12) and BrakeSaver control valve (11) from under the oil pan. The weight is 22 kg (48 lb.).9. Remove elbow (13) from the BrakeSaver control valve. Remove the O-ring seals. The following steps are for installation of the BrakeSaver control valve.10. Inspect the O-ring seals for damage, and make replacements if needed. Put clean engine oil on the O-ring seals.11. Install the O-ring seals and elbow (13) on the BrakeSaver control valve.12. Make sure the O-ring seals are in position on the face of the BrakeSaver control valve. Put BrakeSaver control valve (11) in position under the oil pan. Install bolts (12) that hold the BrakeSaver control valve to the oil pan.13. Install oil temperature sensing unit (4) in the BrakeSaver control valve.14. Connect air line (5) and hose assembly (6) to the BrakeSaver control valve.15. Install the O-ring seals on manifold (2). Install manifold (2) in the BrakeSaver control valve. Install the four bolts that hold the manifold to the BrakeSaver housing.16. Make sure the O-ring seals are in place on the oil lines, and install oil lines (9) and (10).17. Install retainer (8) to hold the oil lines in the BrakeSaver control valve. If the bottom plug in the oil pan was removed, put the split (seam) of the gasket for the plug against the oil pan. If either plug on the side of the oil pan was removed, put 5P3413 Pipe Sealant With Teflon on the threads, and tighten the plug to a torque of 80 11 N m (60 8 lb.ft.).18. Fill the engine with oil to the correct level. See the Maintenance Manual.Disassemble & Assemble BrakeSaver Control Valve
Start By:a. remove BrakeSaver control valve 1. Remove O-ring seals (1) from the valve body.
Covers (3) and (4) hold a spring under compression. To prevent possible personal injury from flying parts, hold covers (3) and (4) when the bolts are removed.
2. Remove four bolts (2) slowly and evenly from cover (4). Remove the cover.3. Remove cover (3) and the seal from the opposite end of the valve body. 4. Remove spool (8) as an assembly.5. Remove spring (7), stop (10), spring (6) and slug (9).6. Remove the O-ring seals and sleeve (5). 7. Remove bolt (11), plate (13) and diaphragm (12) from the spool. Inspect the pin on the spool, and make a replacement of the pin if there is damage or wear. The following steps are for assembly of the BrakeSaver control valve.
When diaphragm (12) is installed on valve spool (8) make sure the fabric side is pulled down over the valve spool to make contact with it and smooth (rubber coated) side is next to the valve body.
8. Put diaphragm (12) in position on valve spool (8).9. Align the hole in plate (13) with the pin in valve spool (8) and install the plate.10. Install bolt (11).11. Install sleeves (5) and the O-ring seals.12. Put spring (7), stop (10), spring (6) and slug (9) in position in valve spool (8).13. Install valve spool (8) into the valve body. As the valve is installed, make sure the edge at the diaphragm makes contact all the way around with the groove in the valve body. At this time the valve spool end must extend approximately 38.1 mm (1.50 in.) from the valve body. Push the valve spool approximately 6.4 mm to 12.7 mm (.25 in. to .50 in.) farther into the valve body until a curved depression is caused between the valve spool and valve body. Make sure there are no wrinkles in the diaphragm.14. Install covers (3) and (4) on the valve body.15. Install three O-ring seals (1).End By:a. install BrakeSaver control valve.


Parts lead EVINRUDE:

0580692
 
0580692 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580691
 
0580691 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0382670
0580731
 
0580731 LEAD, Start solenoid to start motor
55872A, 55972A, 60072B, 60172C, 65272S, 65372R
0279337
 
0279337 LEAD, Horn to cable
100193A, 100293R, 125183C, 125283R, 50172S, 50202C, 60172C, 65272S, 85193A, 85293R
0385200
LEAD ASSY
0385200 LEAD ASSY
100293R, 125183C, 125283R
0580874
Back to top