0382670 EVINRUDE LEAD ASSEMBLY. Spark plug to distributor ( #1 & #3 )


0382670 LEAD ASSEMBLY. Spark plug to distributor ( #1 & #3 ) EVINRUDE 55872A, 55972A, 60072B, 60172C LEAD
0382670 LEAD ASSEMBLY. Spark plug to distributor ( #1 & #3 ) EVINRUDE
Rating:
18

Buy LEAD ASSEMBLY. Spark plug to distributor ( #1 & #3 ) 0382670 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$103.18
 

04-02-2019
631 Hundredths Pounds
OCAP Inter: OCAP International s
Ocap Suspension Arm 0382670
Lenker type: Suspension Arm || Material: Aluminium || Manufacturer's item number: 0382670
Number on catalog scheme: 22
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

55872A, 55872R, 55872S, 55873A, 55873R, 55873S 1968
55972A, 55972C, 55973A, 55973C 1969
60072B, 60072D, 60073B, 60073D 1970
60172C, 60172E, 60173C, 60173E 1971

Information:

Recommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Codes
A. Check for codes
Codes
Result: A diagnostic code is present.
Repair: Troubleshoot the code and make repairs.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Incorrect Parameters
A. Use Cat ET to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
Parameters Result: The parameters are correct.
Proceed to Test Step 3.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
3. Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle Signal Result: The throttle signal is stable.
Proceed to Test Step 4.
Result: The throttle signal is not stable.
Repair: Make the necessary repairs, Refer to the appropriate circuit test.
4. Restriction in the Air Inlet and Exhaust System
A. Observe the check engine lamp. Check for an air filter restriction indicator. Replace any plugged air filters. Refer to the Operation and Maintenance Manual.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions Result: There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 5.
Result: There are restrictions in the air inlet or exhaust system.
Repair: Make the necessary repairs, Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for additional information.
5. Check the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
E. Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation. Cold mode (if applicable) is activated whenever the engine coolant temperature falls below a predetermined value. Monitor the status screen on Cat ET in order to verify that the engine has exited cold mode. Observe the reading for coolant temperature on the Cat ET.
Refer to "Cold Mode Operation" within the Systems Operation, "General Information".
F. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel Quality - Test" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
G. Check for the proper operation of the fuel transfer pump. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information.
Fuel system Result: The fuel pressure is OK.
Proceed to Test Step 6.
Result: The fuel pressure is not OK.
Repair: Replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details.
6. Engine Load
A. Check accessories and parasitic loads on the engine.
Engine loads Result: There is not a parasitic load.
Proceed to Test Step 7.
Result: There is a parasitic load.
Repair: Remove the parasitic load.
7. Valve Lash
A. Check the valve lash. The valve lash can affect the performance of the engine.
Valve lash Result: The valve lash is not set correctly.
Repair: Set the valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.


Parts lead EVINRUDE:

0381626
 
0381626 LEAD,Ignition to choke
100882B, 33802M, 40852A, 40872A, 55872A, 65832B, 85852A, 85892A
0580692
 
0580692 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580691
 
0580691 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580694
 
0580694 LEAD, Assembly, Ground
55872A, 55972A, 65832B, 85852A, 85892A
0580693
 
0580693 LEAD ASSEMBLY, Primary
55872A, 55972A, 65832B, 85852A, 85892A
0279337
 
0279337 LEAD, Horn to cable
100193A, 100293R, 125183C, 125283R, 50172S, 50202C, 60172C, 65272S, 85193A, 85293R
0279340
 
0279340 LEAD, Horn to switch
100193A, 100293R, 125183C, 125283R, 50172S, 50202C, 60172C, 65272S, 85193A, 85293R
Back to top