0383533 LEAD, Primary EVINRUDE
100193A, 85093B, 85193A, 85293R, 85993E
LEAD
Price: query
Rating:
BRP EVINRUDE entire parts catalog list:
- IGNITION SYSTEM » 0383533
85193A, 85193H 1971
85293R 1972
85993E, 85993M, 85993S 1969
Information:
1. Remove cover (1). Steps 2 through 4 are for 3408 Generator Sets only.2. Disconnect oil line (2) from the bottom of the turbocharger. Remove oil line (2) and adapter (4) from the flywheel housing. Remove two plugs (3). 3. Remove the cover from the flywheel housing and install tool (A). Use tool (A) to turn the flywheel until the "V" marks on the front camshaft gear and the idler gear are in alignment. It is necessary to put the "V" marks in alignment on the 3408 Generator Sets so that when the camshaft is installed, the pin in the end of the camshaft is in alignment with the hole in rear camshaft gear (5).4. Install tooling (B) as shown. Remove the four bolts that hold rear camshaft gear (5) on the camshaft. Tighten tooling (B) to disconnect rear camshaft gear (5) from the camshaft. Steps 5 through 7 are for 3412 Generator Sets only.5. Disconnect oil line (6) from the bottom of the turbocharger.6. Remove oil line (6) and elbow (7) from the flywheel housing. Remove two studs (8) that hold elbow (7) on the flywheel housing. 7. Use tool (A) to turn the flywheel enough so that three of four bolts (10) can be removed from rear camshaft gear (9). Install tooling (C) as shown. Remove the last bolt that holds rear camshaft gear (9) in place on the camshaft. Tighten tooling (C) to disconnect rear camshaft gear (9) from the camshaft. 8. Remove two bolts (11) and plate (12) that holds the camshaft in position in the cylinder block.
Be careful not to cause damage to the camshaft bearings when the camshaft is removed.
9. Remove camshaft (13) from the engine. 10. Use tooling (D) and a press to remove front camshaft gear (14) from the camshaft.Install camshaft
Make sure the key for gear (1) is in position on camshaft (2) before gear (1) is installed.1. Heat gear (1) to a maximum temperature of 315°C (600°F). Install gear (1) on camshaft (2). Step 2 is for 3408 Generator Sets only. The 3412 Generator Sets do not have pin (3).2. Install pin (3). Install the pin so it extends 8.76 0.25 mm (.345 .010 in.) above the surface.
Do not let 2P2506 Anti-Seize Compound get on the bearing journals on the camshaft.
3. Put 2P2506 Anti-Seize Compound on the lobes on camshaft (2). Put clean engine oil on the camshaft journals. Step 4 is for 3412 Generator Sets only.4. Turn the crankshaft so that the "V" mark on idler gear (4) is toward the bore for the camshaft.5. Install camshaft (2) in the engine. 6. Make sure "V" mark (5) on the camshaft gear is in alignment with "V" mark (6) on the idler gear. 7. Install plate (7) and the two bolts that hold the camshaft in position in the engine. Steps 8 through 12 are for 3412 Generator Sets only.8. Use tool (B) if necessary to put the bolt holes in rear camshaft gear (8) in alignment with the holes in the camshaft.9. Install one bolt (9) to hold rear camshaft gear (8) on the camshaft. Remove tooling (A). Tighten bolt (9) to a torque of 27 4 N m (20 3 lb.ft.).10. Use tool (B) to turn the flywheel so the three other bolts can be installed in rear camshaft gear (8). Tighten these bolts to a torque of 27 4 N m (20 3 lb.ft.). 11. Put 9S3263 Thread Lock on two studs (12). Install the two studs in the flywheel housing.12. Make sure the gasket is in position between oil line (10) and the bottom of the turbocharger. Make sure the gasket is in position between elbow (11) and the flywheel housing. Install oil line (10) and elbow (11). Steps 13 through 16 are for 3408 Generator Sets only.13. Install the four bolts that hold rear camshaft gear (13) in position on the camshaft. Remove tooling (C).14. Tighten the four bolts that hold rear camshaft gear (13) in place to a torque of 27 4 N m (20 3 lb.ft.). 15. Make sure the gasket is in position between oil line (14) and the bottom of the turbocharger. Make sure the gasket is in position between adapter (16) and the flywheel housing. Install oil line (14) and adapter (16).16. Install two plugs (15).17. Check the camshaft end play with tooling (D). The end play must be 0.10 to 0.25 mm (.004 to .010 in.). 18. Install cover (17).END BY:a) install valve lifters and push rodsb) install timing gear cover
Be careful not to cause damage to the camshaft bearings when the camshaft is removed.
9. Remove camshaft (13) from the engine. 10. Use tooling (D) and a press to remove front camshaft gear (14) from the camshaft.Install camshaft
Make sure the key for gear (1) is in position on camshaft (2) before gear (1) is installed.1. Heat gear (1) to a maximum temperature of 315°C (600°F). Install gear (1) on camshaft (2). Step 2 is for 3408 Generator Sets only. The 3412 Generator Sets do not have pin (3).2. Install pin (3). Install the pin so it extends 8.76 0.25 mm (.345 .010 in.) above the surface.
Do not let 2P2506 Anti-Seize Compound get on the bearing journals on the camshaft.
3. Put 2P2506 Anti-Seize Compound on the lobes on camshaft (2). Put clean engine oil on the camshaft journals. Step 4 is for 3412 Generator Sets only.4. Turn the crankshaft so that the "V" mark on idler gear (4) is toward the bore for the camshaft.5. Install camshaft (2) in the engine. 6. Make sure "V" mark (5) on the camshaft gear is in alignment with "V" mark (6) on the idler gear. 7. Install plate (7) and the two bolts that hold the camshaft in position in the engine. Steps 8 through 12 are for 3412 Generator Sets only.8. Use tool (B) if necessary to put the bolt holes in rear camshaft gear (8) in alignment with the holes in the camshaft.9. Install one bolt (9) to hold rear camshaft gear (8) on the camshaft. Remove tooling (A). Tighten bolt (9) to a torque of 27 4 N m (20 3 lb.ft.).10. Use tool (B) to turn the flywheel so the three other bolts can be installed in rear camshaft gear (8). Tighten these bolts to a torque of 27 4 N m (20 3 lb.ft.). 11. Put 9S3263 Thread Lock on two studs (12). Install the two studs in the flywheel housing.12. Make sure the gasket is in position between oil line (10) and the bottom of the turbocharger. Make sure the gasket is in position between elbow (11) and the flywheel housing. Install oil line (10) and elbow (11). Steps 13 through 16 are for 3408 Generator Sets only.13. Install the four bolts that hold rear camshaft gear (13) in position on the camshaft. Remove tooling (C).14. Tighten the four bolts that hold rear camshaft gear (13) in place to a torque of 27 4 N m (20 3 lb.ft.). 15. Make sure the gasket is in position between oil line (14) and the bottom of the turbocharger. Make sure the gasket is in position between adapter (16) and the flywheel housing. Install oil line (14) and adapter (16).16. Install two plugs (15).17. Check the camshaft end play with tooling (D). The end play must be 0.10 to 0.25 mm (.004 to .010 in.). 18. Install cover (17).END BY:a) install valve lifters and push rodsb) install timing gear cover
Parts lead EVINRUDE:
0580692
0580692 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580691
0580691 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580761
0580761 LEAD ASSEMBLY, #1 spark plug
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0580763
0580763 LEAD ASSEMBLY,, #3 spark plug
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0580762
0580762 LEAD ASSEMBLY, #2 spark plug
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0580764
0580764 LEAD ASSEMBLY, #4
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0383351
0383351 LEAD ASSEMBLY, Ignition to choke switch
115983E, 25702H, 33002M, 33902A, 35602G, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40952R, 40972R, 55972A, 85993E
0383591
0383591 LEAD, Solenoid to switch
100193A, 100293R, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85693D, 85993E, E100MLCSC, E115MLCIH, E11