0580693 EVINRUDE LEAD ASSEMBLY, Primary


0580693 LEAD ASSEMBLY, Primary EVINRUDE 55872A, 55972A, 65832B, 85852A, 85892A LEAD
0580693 LEAD ASSEMBLY, Primary EVINRUDE
Rating:
103

Buy LEAD ASSEMBLY, Primary 0580693 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

55872A, 55872R, 55872S, 55873A, 55873R, 55873S 1968
55972A, 55972C, 55973A, 55973C 1969
65832B, 65833B, 65852B, 65853B 1968
85852A, 85853A 1968
85892A, 85893A 1968

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Incorrect Maintenance Intervals and/or Incorrect Oil
A. Use engine oil that is recommended and change the engine oil at the interval that is recommended by the engines Operation and Maintenance Manual.
Maintenance Intervals
Result: The engine oil was changed at the interval that is recommended by the engines Operation and Maintenance Manual.
Proceed to Test Step 2.
Result: The engine oil was not changed at the interval that is recommended by the engines Operation and Maintenance Manual.
Use at least the minimum grade of Cat oil.
Repair: Change the engine oil at the interval that is recommended. Repair or replace any damaged parts.
2. Contaminated Engine Oil
A. Obtain an S-O-S oil analysis. The analysis will contribute to a better understanding of oil contamination.
B. Check the oil filter bypass valve.
If the oil filter bypass valve is open, the oil will not be filtered. Check the oil filter bypass valve for a weak spring or for a broken spring. If the spring is broken, replace the spring. Verify that the oil bypass valve is operating correctly. Refer to the Disassembly and Assembly manual.
Refer to the Caterpillar guidelines for "Reusability and Salvage/Repair" for determining if the replacement of parts is necessary in order to perform a quality repair.
Contamination
Result: The oil is contaminated.
Repair: Determine the reason for any contamination of the engine oil and make the necessary repairs. Drain the crankcase and refill the crankcase with clean engine oil. Install new engine oil filters. Refer to the engines Operation and Maintenance Manual.
Result: The oil is not contaminated.
Proceed to Test Step 3.
3. Low Oil Pressure
A. Engine oil that is contaminated with another liquid can cause low engine oil pressure. High engine oil level can be an indication of contamination. Obtain an analysis of the engine oil.
B. The inlet screen of the suction tube for the engine oil pump can have a restriction. This restriction will cause cavitation and a loss of engine oil pressure. Check the inlet screen on the suction tube and remove any material that may be restricting engine oil flow.
When some components of the engine show wear in a short time, the cause can be a restriction in a passage for engine oil. An indicator for the engine oil pressure may indicate sufficient pressure, but a component is worn due to a lack of lubrication. In such a case, look at the passage for the engine oil supply to the component. Refer to Systems Operation/Testing and Adjusting, "Lubrication System" for additional information.
Restriction
Result: The inlet tube has a restriction.
Repair: Clear the obstruction. Verify the repair.
Result: The inlet tube does not have a restriction.
Proceed to Test Step 4.
4. Leaks in Air System
A. A leak in the air intake system may allow unfiltered air into the engine. Inspect the air intake system for streaks which may indicate a leakage of unfiltered air. Inspect all of the gaskets and the connections.
Air Leak
Result: There are no air leaks.
Proceed to Test Step 5.
Result: There are air leaks.
Repair: Repair any leaks.
5. Inspect the Fuel Filters for Contamination
A. Remove the fuel filters. Inspect the fuel filters for contamination. Contaminants in the fuel such as hydrogen sulfide and sulfur can lead to the formation of acids in the crankcase. Obtain a fuel analysis.
Fuel Filters
Result: The fuel has contamination.
Repair: Determine the cause of any contamination and make the necessary repairs.
Repair: Install new fuel filters. Refer to the Operation and Maintenance Manual.


Parts lead EVINRUDE:

0382591
 
0382591 LEAD ASSY., #1 spark plug
100882B, 65832B, 85852A, 85892A
0382592
 
0382592 LEAD ASSY., #3 spark plug
100882B, 65832B, 85852A, 85892A
0382593
 
0382593 LEAD ASSY.,#2 & #4 spark plug
100882B, 65832B, 85852A, 85892A
0381626
 
0381626 LEAD,Ignition to choke
100882B, 33802M, 40852A, 40872A, 55872A, 65832B, 85852A, 85892A
0380096
 
0380096 LEAD,Solenoid to starter
100882B, 33002M, 33802M, 33902A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40852A, 40872A, 40952R, 40972R, 65832B, 85852A, 85892A
0580692
 
0580692 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580691
 
0580691 LEAD ASSEMBLY
100193A, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580694
 
0580694 LEAD, Assembly, Ground
55872A, 55972A, 65832B, 85852A, 85892A
Back to top