5001346 EVINRUDE LEAD ASSY., Spark plug


5001346 LEAD ASSY., Spark plug EVINRUDE E200FCSSSC, E200FCXSIF, E200FPLSSC, E200FPXSSC, E225FCXSIF, E225FCXSSC, E225FGLSSC, E225FHLSSS, E225FPLSIF, E225FPXSSC, E250FCXSIF, E250FCXSSS, E250FGLSSS, E250FPXSSS LEAD
5001346 LEAD ASSY., Spark plug EVINRUDE
Rating:
88

Buy LEAD ASSY., Spark plug 5001346 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$9.95
 

14-09-2017
1.00[0.45] pounds
OMC: OMC
5001346 Spark Plug Lead Assembly Evinrude Ficht Electrical Outboard 2000-2003
OMC||5001346||Used, freshwater part||2000-2003||200-250hp
$31.90
 

18-05-2022
0.5[0.00] Pounds
-: -
Ushio 5001346 Light Bulb, 70W EDX17 E26 Base Metal Halide - 4000K - 4000 Lm. (MP70/U/MED/42/PS)
Formed Arc-Tube Body Higher Efficacy Better Color Performance & Consistency Longer Life Faster Starting Time Improved Hot Re-strike Capability
Number on catalog scheme: 37
 

BRP EVINRUDE entire parts catalog list:

E200FCSSSC, E200FCSSSH, E200FCXSSC, E200FCXSSH 2000
E200FCXSIF, E200FPLSIF, E200FPXSIF, E200FSLSIF, RE200FCSIF, RE200FLSIF, RE200FSSIF, RE200FXSIF 2001
E200FPLSSC, E200FPLSSH, E200FSLSSC, E200FSLSSH, RE200FLSSC, RE200FLSSH, RE200FSSH 2000
E200FPXSSC, E200FPXSSH, RE200FXSSC, RE200FXSSH 2000
E225FCXSIF, E225FCZSIF, E225FHLSIF, E225FPXSIF, E225FPZSIF, RE225FCSIF, RE225FHSIF, RE225FXSIF, RE225FZSIF 2001
E225FCXSSC, E225FCXSSH, E225FCZSSC, E225FCZSSH, RE225FCSSC, RE225FCSSH 2000
E225FGLSSC, E225FGLSSH, E225FPLSSC, E225FPLSSH, RE225FGSSC, RE225FGSSH, RE225FLSSC, RE225FLSSH 2000
E225FHLSSS, RE225FHSSS 2000
E225FPLSIF 2001,2003
E225FPXSSC, E225FPXSSH, E225FPZSSC, E225FPZSSH, RE225FXSSC, RE225FXSSH, RE225FZSSH 2000
E250FCXSIF, E250FCZSIF, E250FPXSIF, E250FPZSIF 2001
E250FCXSSS, E250FCZSSS 2000
E250FGLSSS, E250FPLSSS 2000
E250FPXSSS, E250FPZSSS 2000

Information:

If a fault occurs with the primary throttle with secondary throttle is installed, the secondary throttle will be used until the fault is repaired.If a fault occurs with the secondary throttle, the engine will use the primary throttle until the fault is repaired.If a functional throttle is not available, the following conditions will occur:
The engine will default to the limp home speed.
If the engine speed is higher than the limp home speed, the engine will decelerate to the limp home speed.
If the engine speed is lower than the limp home speed, the engine speed will remain at the current speed.
The engine will remain at this speed while the diagnostic code remains active.
All inputs from the faulty throttle are ignored by the ECM until the fault is repaired.
All inputs from the repaired throttle will be ignored by the ECM until the keyswitch has been cycled.The diagnostic codes above relate to an analog sensor. Use this procedure only if the analog sensor uses an output from a variable resistor.The sensor is most likely to be mounted on a throttle pedal. The sensor is attached directly to the throttle assembly. The sensor provides an output voltage to the ECM. The sensor output voltage will vary with the position of the throttle. Foot operated or hand operated throttle assemblies are available.The sensor receives +5 VDC power from the ECM. The sensor will produce a raw signal voltage that will alter between low idle and high idle. The voltage is changed into a throttle position within the range 0% to 100% by the ECM.The sensor senses the speed requirement from the throttle position. A second sensor may override this speed requirement from the first sensor. This override will be subject to an input from a secondary throttle or from the SAE J1939 (CAN) data link or from a PTO control.Use the electronic service tool to check the input status.Note: The identification letters for the terminals in the connectors may vary dependent on the manufacturer of the throttle pedal.During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Illustration 1 g06104722
Schematic of the analog throttle position sensors
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 ECM connector and the analog throttle position sensors.
Refer to Troubleshooting, "Electrical Connector - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the analog throttle position sensor connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the analog throttle position sensors to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: There are no active diagnostic codes for the analog throttle position sensors.
Proceed to Test Step 3.
Result: One or more of the diagnostic codes listed in Table 1 is active.
Proceed to Test Step 5.
3. Check the Throttle Position with the Electronic Service Tool
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position. Do not start the engine.
C. Observe the throttle position reading on the electronic service tool.
D. Operate the throttle over the full range of movement.
20 percent to 27 percent at low idle.
80 percent to 87 percent at high idle
Result: The ECM is not receiving the correct signal from the sensor.
Repair: Use the electronic service tool to verify that the throttle has been configured correctly before continuing with this procedure.
If the fault is still present after the throttle has been configured correctly, replace the analog throttle position sensor.
Result: The sensor is operating correctly.
Proceed to Test Step 4.
4. Check the Throttle Selection Status with the Electronic Service Tool
A. Check the status of the throttle selection switch (if equipped). Use the electronic service tool to check the status of the throttle selection switch.
Throttle 1 has control when status is "OFF".
Throttle 2 has control when status is ON.
Result: The throttle section switch is operating correctly.
Return the engine to service.
If an intermittent fault exists, refer to Troubleshooting, "Electrical Connector - Inspect"
Result: The wrong throttle is selected.
Repair: Switch to the other throttle. There may be a fault with the selector switch input.
Check the connections between the throttle selection switch and the P1 connector. Refer to Troubleshooting, "Electrical Connector - Inspect".
5. Check the Sensor Supply Voltage
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the suspect throttle position sensor.
C. Turn the keyswitch to the ON position.
D. Measure the voltage between the 5 VDC terminal and the ground t


Parts lead EVINRUDE:

0386721
 
0386721 LEAD, Starter to Solenoid
35602G, E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHPLISS, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E200FCSSSC, E200FCXEEN, E200FCXSIF, E200FCXSNF, E200FCXSOE, E200FCXSRB, E200FCXSTM, E200FHLSOR, E200FHLSRC, E200FPLSNF, E2
0584262
 
0584262 LEAD ASSY., Ground
BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, DE225CXINS, DE225PXINS, DE250CXISF, DE250PXISF, DE300CXIIC, DE300CXINR, DE300CXISF, DE300CZIIC, DE300PXIIC, DE300PXINR, DE300PXISF
Back to top