0393959 EVINRUDE LEAF PLATE ASSY.


0393959 LEAF PLATE ASSY. EVINRUDE BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E5DRECR, E6RCCS, E6RCDE, E6RCEC, E6RCOB, E6RCRM, E6RCUD, E6REIA, E6RENM, E6REOD, E6RERE, E6RESR, E6RETB, E8DREEA, E8DRSSM, E8RCCS, E8RCDE, E8RCEC, E8RCOB, E8RCRM, E8R LEAF
0393959 LEAF PLATE ASSY. EVINRUDE
Rating:
99

Buy LEAF PLATE ASSY. 0393959 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

BRP EVINRUDE entire parts catalog list:

BE5DREDS, BE5DRLEDS 1996
BE5DREUC, BE5DRLEUC 1997
BE6DRECR, BE6DRLECR, E6RECR, E6RLECR 1998
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8RCB, BE8RCLB 1997
BE8RCH, BE8RCLH 1996
BE8RCLT, BE8RCT 1998
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E5DRECR, E5DRLECR 1998
E6RCCS, E6RLCCS, E6SLCCS 1988
E6RCDE, E6RLCDE, E6SLCDE 1986
E6RCEC, E6RLCEC, E6SLCEC 1989
E6RCOB, E6RLCOB, E6SLCOB 1985
E6RCRM, E6RLCRM, E6SLCRM 1984
E6RCUD, E6RLCUD, E6SLCUD 1987
E6REIA, E6RLEIA, E6SLEIA 1991
E6RENM, E6RLENM, E6SLENM 1992
E6REOD, E6RLEOD, E6SLEOD 1995
E6RERE, E6RLERE, E6SLERE 1994
E6RESR, E6RLESR, E6SLESR 1990
E6RETB, E6RLETB, E6SLETB 1993
E8DREEA 1999
E8DRSSM 2000
E8RCCS, E8RLCCS, E8SRLCCS 1988
E8RCDE, E8RLCDE, E8SRLCDE 1986
E8RCEC, E8RLCEC, E8SRLCEC, TE8RCEC, TE8RLCEC 1989
E8RCOB, E8RLCOB, E8SRLCOB 1985
E8RCRM, E8RLCRM, E8SRLCRM 1984
E8RCUD, E8RLCUD, E8SRLCUD 1987
E8RECR, E8RLECR, E8SRLECA 1998
E8REIA, E8RLEIA, E8SRLEIA 1991
E8RENM, E8RLENM, E8SRLENM 1992
E8REOD, E8RLEOD, E8SRLEOD 1995
E8RERE, E8RLERE, E8SRLERE 1994
E8RESR, E8RLESR, E8SRLESR, TE8RLESCF 1990
E8RETB, E8RLETB, E8SRLETB 1993
E8REUC, E8RLEUC, E8SRLEUC 1997
E8WREES, E8WRLEES 1999
E8WRLSIR, E8WRSIR 2001
E8WRLSSC, E8WRSSC 2000

Information:

If a fault occurs with the primary throttle with secondary throttle is installed, the secondary throttle will be used until the fault is repaired.If a fault occurs with the secondary throttle, the engine will use the primary throttle until the fault is repaired.If a functional throttle is not available, the following conditions will occur:
The engine will default to the limp home speed.
If the engine speed is higher than the limp home speed, the engine will decelerate to the limp home speed.
If the engine speed is lower than the limp home speed, the engine speed will remain at the current speed.
The engine will remain at this speed while the diagnostic code remains active.
All inputs from the faulty throttle are ignored by the ECM until the fault is repaired.
All inputs from the repaired throttle will be ignored by the ECM until the keyswitch has been cycled.The diagnostic codes above relate to an analog sensor. Use this procedure only if the analog sensor uses an output from a variable resistor.The sensor is most likely to be mounted on a throttle pedal. The sensor is attached directly to the throttle assembly. The sensor provides an output voltage to the ECM. The sensor output voltage will vary with the position of the throttle. Foot operated or hand operated throttle assemblies are available.The sensor receives +5 VDC power from the ECM. The sensor will produce a raw signal voltage that will alter between low idle and high idle. The voltage is changed into a throttle position within the range 0% to 100% by the ECM.The sensor senses the speed requirement from the throttle position. A second sensor may override this speed requirement from the first sensor. This override will be subject to an input from a secondary throttle or from the SAE J1939 (CAN) data link or from a PTO control.Use the electronic service tool in order to check the input status.Note: The identification letters for the terminals in the connectors may vary dependent on the manufacturer of the throttle pedal.During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 ECM connector and the analog throttle position sensors.
Refer to Troubleshooting, "Electrical Connector - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the analog throttle position sensor connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the analog throttle position sensors to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all of the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the


Parts leaf EVINRUDE:

0325267
 
0325267 LEAF VALVE
E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCCS, E6RCDE, E6RCEC, E6RCOB, E6RCRM, E6RCUD, E6RESR, E8RCCS, E8RCDE, E8RCEC, E8RCIC, E8RCNR, E8RCOB, E8RCRM, E8RCSS, E8RCTA, E8RCUD, E8RESR
0390231
 
0390231 LEAF PLATE ASSY.
E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCCS, E6RCDE, E6RCEC, E6RCOB, E6RCRM, E6RCUD, E6RESR, E8RCCS, E8RCDE, E8RCEC, E8RCIC, E8RCNR, E8RCOB, E8RCRM, E8RCSS, E8RCTA, E8RCUD, E8RESR
Back to top