0304807 EVINRUDE LEVER, Locking


0304807 LEVER, Locking EVINRUDE 33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40802A, 40852A, 40902R, 40952R LEVER
0304807 LEVER, Locking EVINRUDE
Rating:
48

Buy LEVER, Locking 0304807 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

BRP EVINRUDE entire parts catalog list:

33002M, 33003M, 33052M, 33053M 1970
33802M, 33802R, 33803M, 33803R, 33852M, 33852R, 33853M, 33853R 1968
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40202E, 40203E, 40252E, 40253E 1972
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40902R, 40903R 1969
40952R, 40953R 1969

Information:


Illustration 1 g01386463
(A) Distance for the plunger lift pin from the rear face of the fuel pump housing ... 9.7 0.5 mm (0.38 0.02 inch) (C) Distance for the spring pin from the top of the fuel pump housing ... 4.78 0.25 mm (0.188 0.010 inch) (D) Distance for the hollow dowel from the top of the fuel pump housing ... 12.19 0.25 mm (0.480 0.010 inch) (E) Installation depth of the sleeve bearings ... 19.0 0.5 mm (0.75 0.02 inch) (F) Inside diameter of the sleeve bearings after installation ... 12.758 0.046 mm (0.5023 0.0018 inch) (J) Inside diameter of the sleeve bearings after installation ... 53.988 0.038 mm (2.1255 0.0015 inch) (K) Distance for the hollow dowel from the bottom face of the fuel pump housing ... 1.5 0.3 mm (0.06 0.01 inch) (L) Maximum distance for the hollow dowel from the bottom face of the fuel pump housing ... 4.8 0.5 mm (0.19 0.02 inch) (M) Install the hollow dowel for the oil inlet to a maximum distance from the bottom face of the fuel pump housing. ... 1.0 mm (0.04 inch) (N) Install the front sleeve bearing to the following dimension from the front face of the fuel pump housing. ... 1.0 0.5 mm (0.04 0.02 inch) (P) Install the dowel in order to get a dimension from the centerline of fuel injection pump bore to dowel. ... 14.76 0.10 mm (0.581 0.004 inch)Note: Seal the dowel hole with aluminum ball (3) . (R) Locate the joint of the sleeve bearing for the camshaft to the following angle to the left of the centerline. ... 30 1 degrees (S) Maximum angle for location of oil hole in sleeve bearings ... 30 1 degrees (T) Angle for sleeve bearings above fuel pump camshaft's centerline ... 45 1 degrees (1) Push the end of the sleeve bearing with a sharp corner to 0.15 mm (0.006 inch) below the surface. The notch of the sleeve bearing must be oriented with the oil hole. (2) The center of the tab for the sleeve bearing must be within 0.05 mm (0.002 inch) of a line that passes through the center of the bearing inside diameter that is parallel to the vertical centerline of the fuel pump housing.
Illustration 2 g01386494
(U) Install the pump idler shaft to the following distance from the top of the fuel pump housing. ... 16.8 0.5 mm (0.66 0.02 inch) (W) Inside diameter of the sleeve bearing after installation ... 19.093 0.038 mm (0.7517 0.0015 inch) (X) Install the sleeve bearing to the following depth from the top of the fuel pump housing. ... 28.4 0.5 mm (1.12 0.02 inch) (Y) Locate the joints of the sleeve bearing to the following angle. ... 10 5 degrees (4) Install the sleeve bearing within the following dimension from the top of the fuel pump housing. ... 0.15 mm (0.006 inch) (5) During installation, the lifter guide pin should be pressed into the bore until contact is made with the bottom of the casting.


Parts lever EVINRUDE:

0303749
 
0303749 LEVER
33002M, 33802M, 33902A, 40102B
0303747
 
0303747 LEVER
25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25904R, 33002M, 33802M, 33902A, 35602G, 40102B, E25ECIB, E25RCSA, E35ECIG, E35ECSM
0305288
LEVER, Shifter
0305288 LEVER, Shifter
33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40902R, 40952R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0303954
 
0303954 LEVER, Locking, reverse
33002M, 33802M, 33902A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0378985
 
0378985 LEVER, Throttle
40002A, 40052A, 40072A, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0378041
LEVER, Choke
0378041 LEVER, Choke
40002A, 40052A, 40072A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0380329
LEVER, Lock out
0380329 LEVER, Lock out
40002A, 40052A, 40802A, 40852A, 40902R, 40952R
0305269
 
0305269 LEVER, Reverse locking
40002A, 40052A, 40072A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
Back to top