0315110 EVINRUDE LEVER, Throttle


0315110 LEVER, Throttle EVINRUDE 115083D, 115983E, 85093B, 85993E LEVER
0315110 LEVER, Throttle EVINRUDE
Rating:
103

Buy LEVER, Throttle 0315110 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
£47.99
 

15-09-2017

Toffeln: Toffeln
Toffeln 03151-10 Safety Lite Clog, Size 10
Conforms To Professional Quality Standards, Ergonomic Design, Heel Strap, High-Tech S2 Material||High quality||High performance
Number on catalog scheme: 82
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

115083D 1970
115983E, 115983S 1969
85093B, 85093D 1970
85993E, 85993M, 85993S 1969

Information:

Start By:a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) which points to the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through NO. 6 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plate from each side of the No. 4 upper main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until Tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. The following steps are for the installation of the crankshaft main bearings.
Make sure the upper and lower halves of bearings are installed so bearing tabs (5) fit into the notch in cylinder block and bearing caps.
Do not put oil on the parts until the bearing clearance has been checked.5. Put clean engine oil on the lower. Install lower bearings in the bearing caps,6. Put clean engine oil on the upper bearings. Install upper bearings in the cylinder block with Tool (A). When the bearing clearance is checked and the engine is in a vertical position such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearing to get the correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.7. Check the bearing clearance with Plastigage (B) as follows: a. Put a piece of the Plastigage on the surface of the lower bearing half.b. install the main bearing caps with arrow (6) toward the front of the cylinder block. Each cap has a number (7) on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put 2P-2506 Thread Lubricant on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb ft).f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120 degrees (1/3 of a turn). Tighten the bolts on the tab end of the cap 120 degrees (1/3 of a turn).
Do not use an impact wrench to tighten the bolts the additional 120 degrees (1/3 of a turn).
8. Remove the caps and measure the Plastigage. The clearance for new bearings must be 0.091 to 0.018 mm (.0036 to .0073 in). The maximum clearance for used bearings is 0.25 mm(.010 in).9. Install a thrust plate (8) on each side of the No. 4 upper bearing. Install the thrust plates with the side marked "Block Side" toward the cylinder block.10. Install again the No. 2 through No. 6 main bearing caps. Follow the tightening procedure in Step 7.11. Do Steps, 2,4,5,6,7 and 8 for the No. 1 and No. 7 main bearing caps. 12. Check the crankshaft end play with Tool (C). The end play is controlled by the thrust plates on the center main bearing. Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.15 to 0.51 mm (.006 to .020 in). The maximum end play with used thrust plates is 0.89 mm (.035 in).End By:a. install oil pump


Parts lever EVINRUDE:

0278346
 
0278346 LEVER,Throttle
100882B, 115983E, 40072A, 40972R, 55872A, 55972A, 85892A, 85993E
0308043
 
0308043 LEVER,Idle adjustment
100882B, 115983E, 40072A, 40872A, 40972R, 55872A, 55972A, 85892A, 85993E
0382370
 
0382370 LEVER ARM & PIN ASSEMBLY
100193A, 100293R, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55872A,
0314895
 
0314895 LEVER, Manual choke
100193A, 100293R, 115083D, 115393M, 115493B, 115983E, 125183C, 125283R, 135383M, 135443B, 85093B, 85193A, 85293R, 85393M, 85493B, 85993E
0315109
LEVER, Spark advance
0315109 LEVER, Spark advance
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0279171
 
0279171 LEVER ARM & FRICTION ROD ASSEMBLY
100193A, 100293R, 115083D, 125183C, 125283R, 50172S, 50202C, 60072B, 60172C, 65272S, 85093B, 85193A, 85293R
Back to top