0329225 EVINRUDE LEVER, Spark advance

Table 1
Diagnostic Codes Table
Code and Description Conditions which Generate this Code System Response
3509-3 Sensor Supply Voltage 1 : Voltage Above Normal The Electronic Control Module (ECM) detects a voltage for the 5 V power supply that is above 5.2 V for one second. The code is logged.
The amber warning lamp is illuminated.
The ECM will use the last good value for each parameter that uses the 5 V supply.
The service tool displays "Data Error" on the status screen for all of the 8 V sensors and the sensor supply.
3509-4 Sensor Supply Voltage 1 : Voltage Below Normal The ECM detects a voltage for the 5 V power supply that is below 4.8 V for one second. The code is logged.
The amber warning lamp is illuminated.
The ECM will use the last good value for each parameter that uses the 5 V supply.
The service tool displays "Data Error" on the status screen for all of the 8 V sensors and the sensor supply.
The ECM retries the circuit at two second intervals in order to recheck the circuit.
3511-6 Sensor Supply Voltage 3 : Current Above Normal While the output driver for the oxygen sensors is on, the ECM detects a high current in the circuit for two seconds. The code is logged.
The amber warning lamp is illuminated.
The activation of this code is latched by the ECM. The power to the ECM must be powered in order to reset the power supply. 24 V Power SupplyThe ECM supplies 24 VDC to the voltage converter for the oxygen sensors through terminal location P1-28 at the ECM.The 3511-6 becomes activated if a short to ground is detected in the harness between the ECM and the voltage converter.8 V Power SupplyThe ECM supplies 8 VDC to the speed/timing sensor.For information that is related to troubleshooting the circuit for the speed/timing sensor, refer to Troubleshooting, "Speed/Timing - Test" for details.5 V Power SupplyThe ECM supplies 5.0 0.2 VDC to the following sensors:
Engine oil pressure sensor
Intake manifold pressure sensor
Temperature sensor at the inlet of the catalytic converter
Temperature sensor at the outlet of the catalytic converterThe ECM also provides 5.0 0.2 VDC to the speed control potentiometer.There are five outputs at the ECM for the 5 V sensor supply:
J1-41
J1-42
J2-46
J2-48The internal circuitry for the outputs is wired to the same voltage source inside the ECM. A short circuit on one of these terminals will cause a short circuit on the other terminal. A 3509-4 Sensor Supply Voltage 1 : Voltage Below Normal will be activated if the following conditions occur:
The desired speed signal wire is shorted to ground.
The speed control potentiometer is near the maximum desired speed or at the maximum desired speed.A diagnostic code for the 5 V power supply is probably caused by a short circuit or by an open circuit in a harness. The next likely cause is a sensor problem. The least likely cause is a problem with the ECM.
Illustration 1 g03673417
Schematic for the power supply circuits
Test Step 1. Inspect the Electrical Connectors and the Wiring
Set the engine control switch to the OFF position. Remove the electrical power from the engine.
Illustration 2 g01960583
Locations of the engine sensors that are associated with the sensor supply circuits (typical left side engine view)
(1) Intake manifold pressure sensor
Illustration 3 g02073893
Locations of the engine sensors that are associated with the sensor supply circuits (typical right side engine view)
(2) Voltage converter
(3) Engine oil pressure sensor
Illustration 4 g02073953
Locations of the ECM connectors that are associated with the sensor supply circuits (typical right side engine view)
(4) J2/P2 ECM connector
(5) J1/P1 ECM connector
(6) Interconnect harness connector
Thoroughly inspect the condition of the connectors that are for sensors (1) and (3). Inspect the condition of connectors (2) that are at the voltage converter and connectors (6) that are for the interconnect harness. Also, thoroughly inspect the condition of ECM connectors (4) and (5). Refer to Testing and Adjusting, "Electrical Connectors - Inspect".
Illustration 5 g02073973
Terminal locations at the P1 ECM connector that are for the sensor supply circuit
(P1-29) 24 V supply for the voltage converter
(P1-34) Return for the temperature sensors that are for the catalytic converter
(P1-41) 5 V supply for the temperature sensors that are for the catalytic converter
(P1-42) 5 V supply for the intake manifold pressure sensor
Illustration 6 g03678638
Terminal locations at the P2 ECM connector that are for the sensor supply circuit
(P2-37) Return for the intake manifold pressure sensor
(P2-38) Return for the engine oil pressure sensor
(P2-40) Return for the desired speed signal
(P2-46) 5 V supply for the engine oil pressure sensor
(P2-48) 5 V supply for the desired speed signal
Illustration 7 g03673507
Terminal locations at the interconnect harness connector that are for the speed adjust potentiometer
(Terminal g) Return for the speed adjust potentiometer
(Terminal n) Desired speed signal for the speed adjust potentiometer
(Terminal N) Supply for the speed adjust potentiometer Show/hide t